Guest Anton Jansen Posted July 14, 2007 Posted July 14, 2007 Whenever the PC goes on standby or shuts down, then powers up again, the system does not recognise the webcam. I have an Intel board and chipset. I have contacted the manufacturer of the cam on two occassions and they claim that the only way to solve the problem is to change the IRQs. I have 6 USB ports on board and everything works except the cam. Someone else suggested to upgrade the BIOS. I have had the run around on the Intel site, indentified my motherboard and chipset but there is no way I can sort this out. Can anyone please assist with a positive solution to this problem.
Guest Uncle Grumpy Posted July 14, 2007 Posted July 14, 2007 Re: WEBCAM USB BIOS PROBLEM Anton Jansen <AntonJansen@discussions.microsoft.com> wrote: >Whenever the PC goes on standby or shuts down, then powers up again, the >system does not recognise the webcam. From the sounds of it, at SOME point you get the system to recognize it, right? Then if the computer goes on standby or shuts down, that recognition is lost. Right? What do you do that causes the system to recognize it?
Guest Elmo Posted July 14, 2007 Posted July 14, 2007 Re: WEBCAM USB BIOS PROBLEM Anton Jansen wrote: > Whenever the PC goes on standby or shuts down, then powers up again, the > system does not recognize the webcam. I have an Intel board and chipset. I > have contacted the manufacturer of the cam on two occasions and they claim > that the only way to solve the problem is to change the IRQs. I have 6 USB > ports on board and everything works except the cam. Someone else suggested to > upgrade the BIOS. I have had the runaround on the Intel site, identified my > motherboard and chipset but there is no way I can sort this out. Can anyone > please assist with a positive solution to this problem? Open Device Manager, open the properties on each USB port, in turn, click the Power tab, and deselect "Allow the computer to turn off this device to save power". -- Joe =o)
Guest Anton Jansen Posted July 14, 2007 Posted July 14, 2007 Re: WEBCAM USB BIOS PROBLEM Sorry Uncle Grumpy, I left out the most importamt comment. The only way the cam works is to unplug it (after bootup) and re-plug it. It then works. When powering down, the recognition is lost. "Uncle Grumpy" wrote: > Anton Jansen <AntonJansen@discussions.microsoft.com> wrote: > > >Whenever the PC goes on standby or shuts down, then powers up again, the > >system does not recognise the webcam. > > From the sounds of it, at SOME point you get the system to recognize > it, right? Then if the computer goes on standby or shuts down, that > recognition is lost. Right? > > What do you do that causes the system to recognize it? >
Guest Anton Jansen Posted July 14, 2007 Posted July 14, 2007 Re: WEBCAM USB BIOS PROBLEM Joe thanks for your info BUt it did not fix the problem, I have turned all the power tabs back ON. "Elmo" wrote: > Anton Jansen wrote: > > Whenever the PC goes on standby or shuts down, then powers up again, the > > system does not recognize the webcam. I have an Intel board and chipset. I > > have contacted the manufacturer of the cam on two occasions and they claim > > that the only way to solve the problem is to change the IRQs. I have 6 USB > > ports on board and everything works except the cam. Someone else suggested to > > upgrade the BIOS. I have had the runaround on the Intel site, identified my > > motherboard and chipset but there is no way I can sort this out. Can anyone > > please assist with a positive solution to this problem? > > Open Device Manager, open the properties on each USB port, in turn, > click the Power tab, and deselect "Allow the computer to turn off this > device to save power". > > -- > Joe =o) >
Guest RalfG Posted July 14, 2007 Posted July 14, 2007 Re: WEBCAM USB BIOS PROBLEM Have you checked at the camera manufacturer for known issues? Some devices simply are not compatible with Standby or Hybernation. "Anton Jansen" <AntonJansen@discussions.microsoft.com> wrote in message news:82043259-F6D9-4F2A-B8A6-435F7CED2C67@microsoft.com... > Joe thanks for your info BUt it did not fix the problem, I have turned all > the power tabs back ON. > > "Elmo" wrote: > >> Anton Jansen wrote: >> > Whenever the PC goes on standby or shuts down, then powers up again, >> > the >> > system does not recognize the webcam. I have an Intel board and >> > chipset. I >> > have contacted the manufacturer of the cam on two occasions and they >> > claim >> > that the only way to solve the problem is to change the IRQs. I have 6 >> > USB >> > ports on board and everything works except the cam. Someone else >> > suggested to >> > upgrade the BIOS. I have had the runaround on the Intel site, >> > identified my >> > motherboard and chipset but there is no way I can sort this out. Can >> > anyone >> > please assist with a positive solution to this problem? >> >> Open Device Manager, open the properties on each USB port, in turn, >> click the Power tab, and deselect "Allow the computer to turn off this >> device to save power". >> >> -- >> Joe =o) >>
Guest Anton Jansen Posted July 15, 2007 Posted July 15, 2007 Re: WEBCAM USB BIOS PROBLEM Ralfg thks. As mentioned in orignal thread, I have contacted Logitech in the Netherlands on two occassions and they claim it's not the cam. It has to do with the USB or IRQs settings. "RalfG" wrote: > Have you checked at the camera manufacturer for known issues? Some devices > simply are not compatible with Standby or Hybernation. > > "Anton Jansen" <AntonJansen@discussions.microsoft.com> wrote in message > news:82043259-F6D9-4F2A-B8A6-435F7CED2C67@microsoft.com... > > Joe thanks for your info BUt it did not fix the problem, I have turned all > > the power tabs back ON. > > > > "Elmo" wrote: > > > >> Anton Jansen wrote: > >> > Whenever the PC goes on standby or shuts down, then powers up again, > >> > the > >> > system does not recognize the webcam. I have an Intel board and > >> > chipset. I > >> > have contacted the manufacturer of the cam on two occasions and they > >> > claim > >> > that the only way to solve the problem is to change the IRQs. I have 6 > >> > USB > >> > ports on board and everything works except the cam. Someone else > >> > suggested to > >> > upgrade the BIOS. I have had the runaround on the Intel site, > >> > identified my > >> > motherboard and chipset but there is no way I can sort this out. Can > >> > anyone > >> > please assist with a positive solution to this problem? > >> > >> Open Device Manager, open the properties on each USB port, in turn, > >> click the Power tab, and deselect "Allow the computer to turn off this > >> device to save power". > >> > >> -- > >> Joe =o) > >> > > >
Guest Elmo Posted July 15, 2007 Posted July 15, 2007 Re: WEBCAM USB BIOS PROBLEM Anton Jansen wrote: > Joe thanks for your info BUt it did not fix the problem, I have turned all > the power tabs back ON. > > "Elmo" wrote: > >> Anton Jansen wrote: >>> Whenever the PC goes on standby or shuts down, then powers up again, the >>> system does not recognize the webcam. I have an Intel board and chipset. I >>> have contacted the manufacturer of the cam on two occasions and they claim >>> that the only way to solve the problem is to change the IRQs. I have 6 USB >>> ports on board and everything works except the cam. Someone else suggested to >>> upgrade the BIOS. I have had the runaround on the Intel site, identified my >>> motherboard and chipset but there is no way I can sort this out. Can anyone >>> please assist with a positive solution to this problem? >> Open Device Manager, open the properties on each USB port, in turn, >> click the Power tab, and deselect "Allow the computer to turn off this >> device to save power". Here are a couple of help sites: http://www.usbman.com/WinME%20USB%20Guide.htm General USB troubleshooting in Windows XP http://support.microsoft.com/kb/310575 -- Joe =o)
Guest RalfG Posted July 15, 2007 Posted July 15, 2007 Re: WEBCAM USB BIOS PROBLEM Considering that it is difficult if not impossible to get XP to change device IRQs, that advice from Logitech sounds a bit like a runaround. :) You can see in XP's System Information which devices are sharing the IRQ with your USB controller(s). I have 6 other devices sharing an IRQ with one of my USB controllers and whatever I tried XP always put them back together on the same IRQ. Here is a page from Logitech US describing computer chipsets that can cause your exact problem and some possible fixes. Intel isn't supposed to be one of the problematic ones. In case the link doesn't work the article has Answer ID 834, from the Logitech US Troubleshooting site. Since the chipset is Intel it may end up that the last suggestion (an add-in USB card) on the page will be the one you need. http://logitech-en-amr.custhelp.com/cgi-bin/logitech_en_amr.cfg/php/enduser/std_adp.php?p_faqid=834&p_created=1089147173&p_sid=t8cAQFGi&p_accessibility=0&p_lva=&p_sp=cF9zcmNoPTEmcF9zb3J0X2J5PSZwX2dyaWRzb3J0PSZwX3Jvd19jbnQ9NiZwX3Byb2RzPTg0NCw1JnBfY2F0cz0mcF9wdj0yLjUmcF9jdj0mcF9zZWFyY2hfdHlwZT1hbnN3ZXJzLnNlYXJjaF9ubCZwX3BhZ2U9MSZwX3NlYXJjaF90ZXh0PWNhbWVyYSBub3QgZm91bmQgYWZ0ZXI*&p_li=&p_topview=1 "Anton Jansen" <AntonJansen@discussions.microsoft.com> wrote in message news:4AA866D7-5838-4861-9027-B7DA256DD39C@microsoft.com... > Ralfg thks. As mentioned in orignal thread, I have contacted Logitech in > the > Netherlands on two occassions and they claim it's not the cam. It has to > do > with the USB or IRQs settings. > > "RalfG" wrote: > >> Have you checked at the camera manufacturer for known issues? Some >> devices >> simply are not compatible with Standby or Hybernation. >> >> "Anton Jansen" <AntonJansen@discussions.microsoft.com> wrote in message >> news:82043259-F6D9-4F2A-B8A6-435F7CED2C67@microsoft.com... >> > Joe thanks for your info BUt it did not fix the problem, I have turned >> > all >> > the power tabs back ON. >> > >> > "Elmo" wrote: >> > >> >> Anton Jansen wrote: >> >> > Whenever the PC goes on standby or shuts down, then powers up again, >> >> > the >> >> > system does not recognize the webcam. I have an Intel board and >> >> > chipset. I >> >> > have contacted the manufacturer of the cam on two occasions and they >> >> > claim >> >> > that the only way to solve the problem is to change the IRQs. I >> >> > have 6 >> >> > USB >> >> > ports on board and everything works except the cam. Someone else >> >> > suggested to >> >> > upgrade the BIOS. I have had the runaround on the Intel site, >> >> > identified my >> >> > motherboard and chipset but there is no way I can sort this out. >> >> > Can >> >> > anyone >> >> > please assist with a positive solution to this problem? >> >> >> >> Open Device Manager, open the properties on each USB port, in turn, >> >> click the Power tab, and deselect "Allow the computer to turn off this >> >> device to save power". >> >> >> >> -- >> >> Joe =o) >> >> >> >> >>
Recommended Posts