Cant access XP Pro normal/safe/last good config

[Guest abd08]

Hi all,

 

I have a PC at work which I did a clean install of XP Pro on a few

weeks ago. It has been used very infrequently only by me, for non-

internet purposes (so no viruses/spyware etc for sure - and I am the

only person with access to this office).

 

Yesterday morning I came into work to find that one of my PCs did not

power on at all. The following happened (in order):

 

1. Switched PSU off from back, turned it on again - no result

2. Unplugged and re-plugged power cable in case it was loose - no

result

3. Switch power cable for another one - the PC powers on

 

- NOTE : The "faulty" cable works on another PC - and I'm not crazy!

=)

 

4. When PC powers on, get an error message saying BIOS config not set.

Upon entering BIOS, date is 2003 etc as if someone had completely

reset the BIOS.

5. Entered the basic details (date etc) and turned on PC - everything

worked

 

6. Yesterday, night, tried to shut-down, but after shutting down, the

computer powered itself on again after about 3 or 4 seconds. Tested

and re-tested this - in the end, I waited for it to power off, and

then turned it off from the power switch on the back of the PSU

 

7. Finally, this morning came in and turned it on again - system wont

go into windows normally, or into safe mode, or into last known good

configuration. Each time, it just reboots itself.

 

What would be the logical order to proceed in order to correct this

problem? My gut tells me to check out the PSU first, but I am not

aware/sure if the PSU can be responsible for the reset command.

 

Thanks in advance,

Raj

[Guest abd08]

Re: Cant access XP Pro normal/safe/last good config

 

Sorry, forgot to add, disabling automatic restart on system failure

didn't help

 

Thanks!

Raj

[Guest Pegasus \(MVP\)]

Re: Cant access XP Pro normal/safe/last good config

 

 

"abd08" <dejaonly@hotmail.com> wrote in message

news:d108cab0-3fa6-41bf-bac1-ab7d382c9822@2g2000hsn.googlegroups.com...

> Hi all,

>

> I have a PC at work which I did a clean install of XP Pro on a few

> weeks ago. It has been used very infrequently only by me, for non-

> internet purposes (so no viruses/spyware etc for sure - and I am the

> only person with access to this office).

>

> Yesterday morning I came into work to find that one of my PCs did not

> power on at all. The following happened (in order):

>

> 1. Switched PSU off from back, turned it on again - no result

> 2. Unplugged and re-plugged power cable in case it was loose - no

> result

> 3. Switch power cable for another one - the PC powers on

>

> - NOTE : The "faulty" cable works on another PC - and I'm not crazy!

> =)

>

> 4. When PC powers on, get an error message saying BIOS config not set.

> Upon entering BIOS, date is 2003 etc as if someone had completely

> reset the BIOS.

> 5. Entered the basic details (date etc) and turned on PC - everything

> worked

>

> 6. Yesterday, night, tried to shut-down, but after shutting down, the

> computer powered itself on again after about 3 or 4 seconds. Tested

> and re-tested this - in the end, I waited for it to power off, and

> then turned it off from the power switch on the back of the PSU

>

> 7. Finally, this morning came in and turned it on again - system wont

> go into windows normally, or into safe mode, or into last known good

> configuration. Each time, it just reboots itself.

>

> What would be the logical order to proceed in order to correct this

> problem? My gut tells me to check out the PSU first, but I am not

> aware/sure if the PSU can be responsible for the reset command.

>

> Thanks in advance,

> Raj

 

You posted your question in a Windows newsgroup but from

your description it would appear that the problem has nothing

at all to do with Windows. I would try a hardware newsgroup.

[Guest Mick Murphy]

RE: Cant access XP Pro normal/safe/last good config

 

1. If your power cable works, change PSU to test original PSU.

2. If BIOS date has changed back to 2003, change the trickle feed coin sized

battery in the motherboard, as that is a sign that that is flat.

 

3. If you always leave your computer on at the power point, I would say

trickle feed battery flat for a while; PSU, or cable failed, causing main

prob.

--

Mick Murphy - Qld - Australia

 

 

"abd08" wrote:

> Hi all,

>

> I have a PC at work which I did a clean install of XP Pro on a few

> weeks ago. It has been used very infrequently only by me, for non-

> internet purposes (so no viruses/spyware etc for sure - and I am the

> only person with access to this office).

>

> Yesterday morning I came into work to find that one of my PCs did not

> power on at all. The following happened (in order):

>

> 1. Switched PSU off from back, turned it on again - no result

> 2. Unplugged and re-plugged power cable in case it was loose - no

> result

> 3. Switch power cable for another one - the PC powers on

>

> - NOTE : The "faulty" cable works on another PC - and I'm not crazy!

> =)

>

> 4. When PC powers on, get an error message saying BIOS config not set.

> Upon entering BIOS, date is 2003 etc as if someone had completely

> reset the BIOS.

> 5. Entered the basic details (date etc) and turned on PC - everything

> worked

>

> 6. Yesterday, night, tried to shut-down, but after shutting down, the

> computer powered itself on again after about 3 or 4 seconds. Tested

> and re-tested this - in the end, I waited for it to power off, and

> then turned it off from the power switch on the back of the PSU

>

> 7. Finally, this morning came in and turned it on again - system wont

> go into windows normally, or into safe mode, or into last known good

> configuration. Each time, it just reboots itself.

>

> What would be the logical order to proceed in order to correct this

> problem? My gut tells me to check out the PSU first, but I am not

> aware/sure if the PSU can be responsible for the reset command.

>

> Thanks in advance,

> Raj

>

[Guest abd08]

Re: Cant access XP Pro normal/safe/last good config

 

On Aug 7, 9:00 am, "Pegasus \(MVP\)" <I....@fly.com.oz> wrote:

> "abd08" <dejao...@hotmail.com> wrote in message

>

> news:d108cab0-3fa6-41bf-bac1-ab7d382c9822@2g2000hsn.googlegroups.com...

>

>

>

> > Hi all,

>

> > I have a PC at work which I did a clean install of XP Pro on a few

> > weeks ago. It has been used very infrequently only by me, for non-

> > internet purposes (so no viruses/spyware etc for sure - and I am the

> > only person with access to this office).

>

> > Yesterday morning I came into work to find that one of my PCs did not

> > power on at all. The following happened (in order):

>

> > 1. Switched PSU off from back, turned it on again - no result

> > 2. Unplugged and re-plugged power cable in case it was loose - no

> > result

> > 3. Switch power cable for another one - the PC powers on

>

> > - NOTE : The "faulty" cable works on another PC - and I'm not crazy!

> > =)

>

> > 4. When PC powers on, get an error message saying BIOS config not set.

> > Upon entering BIOS, date is 2003 etc as if someone had completely

> > reset the BIOS.

> > 5. Entered the basic details (date etc) and turned on PC - everything

> > worked

>

> > 6. Yesterday, night, tried to shut-down, but after shutting down, the

> > computer powered itself on again after about 3 or 4 seconds. Tested

> > and re-tested this - in the end, I waited for it to power off, and

> > then turned it off from the power switch on the back of the PSU

>

> > 7. Finally, this morning came in and turned it on again - system wont

> > go into windows normally, or into safe mode, or into last known good

> > configuration. Each time, it just reboots itself.

>

> > What would be the logical order to proceed in order to correct this

> > problem? My gut tells me to check out the PSU first, but I am not

> > aware/sure if the PSU can be responsible for the reset command.

>

> > Thanks in advance,

> > Raj

>

> You posted your question in a Windows newsgroup but from

> your description it would appear that the problem has nothing

> at all to do with Windows. I would try a hardware newsgroup.

 

Mmm... well, if the system is rebooting during the windows startup

process, then surely windows must be playing some part in it? I have

left the screen at the F8 menu, and the system hasn't restarted itself

for a good hour now.

[Guest M.I.5¾]

Re: Cant access XP Pro normal/safe/last good config

 

 

"abd08" <dejaonly@hotmail.com> wrote in message

news:d108cab0-3fa6-41bf-bac1-ab7d382c9822@2g2000hsn.googlegroups.com...

> Hi all,

>

> I have a PC at work which I did a clean install of XP Pro on a few

> weeks ago. It has been used very infrequently only by me, for non-

> internet purposes (so no viruses/spyware etc for sure - and I am the

> only person with access to this office).

>

> Yesterday morning I came into work to find that one of my PCs did not

> power on at all. The following happened (in order):

>

> 1. Switched PSU off from back, turned it on again - no result

> 2. Unplugged and re-plugged power cable in case it was loose - no

> result

> 3. Switch power cable for another one - the PC powers on

>

> - NOTE : The "faulty" cable works on another PC - and I'm not crazy!

> =)

>

> 4. When PC powers on, get an error message saying BIOS config not set.

> Upon entering BIOS, date is 2003 etc as if someone had completely

> reset the BIOS.

> 5. Entered the basic details (date etc) and turned on PC - everything

> worked

>

> 6. Yesterday, night, tried to shut-down, but after shutting down, the

> computer powered itself on again after about 3 or 4 seconds. Tested

> and re-tested this - in the end, I waited for it to power off, and

> then turned it off from the power switch on the back of the PSU

>

> 7. Finally, this morning came in and turned it on again - system wont

> go into windows normally, or into safe mode, or into last known good

> configuration. Each time, it just reboots itself.

>

> What would be the logical order to proceed in order to correct this

> problem? My gut tells me to check out the PSU first, but I am not

> aware/sure if the PSU can be responsible for the reset command.

>

 

It sounds as though the BIOS battery is flat. This is usually a small coin

sized battery mounted on the motherboard somwhere. It is usually a type

CR2032, but yours may vary. Disconnect the mains and then remove the old

battery. Wait about a quarter of an hour or so before inserting the new

one.

[Guest abd08]

Re: Cant access XP Pro normal/safe/last good config

 

On Aug 7, 9:58 am, "M.I.5¾" <no....@no.where.NO_SPAM.co.uk> wrote:

> "abd08" <dejao...@hotmail.com> wrote in message

>

> news:d108cab0-3fa6-41bf-bac1-ab7d382c9822@2g2000hsn.googlegroups.com...

>

>

>

> > Hi all,

>

> > I have a PC at work which I did a clean install of XP Pro on a few

> > weeks ago. It has been used very infrequently only by me, for non-

> > internet purposes (so no viruses/spyware etc for sure - and I am the

> > only person with access to this office).

>

> > Yesterday morning I came into work to find that one of my PCs did not

> > power on at all. The following happened (in order):

>

> > 1. Switched PSU off from back, turned it on again - no result

> > 2. Unplugged and re-plugged power cable in case it was loose - no

> > result

> > 3. Switch power cable for another one - the PC powers on

>

> > - NOTE : The "faulty" cable works on another PC - and I'm not crazy!

> > =)

>

> > 4. When PC powers on, get an error message saying BIOS config not set.

> > Upon entering BIOS, date is 2003 etc as if someone had completely

> > reset the BIOS.

> > 5. Entered the basic details (date etc) and turned on PC - everything

> > worked

>

> > 6. Yesterday, night, tried to shut-down, but after shutting down, the

> > computer powered itself on again after about 3 or 4 seconds. Tested

> > and re-tested this - in the end, I waited for it to power off, and

> > then turned it off from the power switch on the back of the PSU

>

> > 7. Finally, this morning came in and turned it on again - system wont

> > go into windows normally, or into safe mode, or into last known good

> > configuration. Each time, it just reboots itself.

>

> > What would be the logical order to proceed in order to correct this

> > problem? My gut tells me to check out the PSU first, but I am not

> > aware/sure if the PSU can be responsible for the reset command.

>

> It sounds as though the BIOS battery is flat.  This is usually a small coin

> sized battery mounted on the motherboard somwhere.  It is usually a type

> CR2032, but yours may vary.  Disconnect the mains and then remove the old

> battery.  Wait about a quarter of an hour or so before inserting the new

> one.

 

Thanks for the input, will give it a try and let you know how I get on

tm.

 

Thanks again,

Raj

[Guest HeyBub]

Re: Cant access XP Pro normal/safe/last good config

 

abd08 wrote:

> Hi all,

>

> I have a PC at work which I did a clean install of XP Pro on a few

> weeks ago. It has been used very infrequently only by me, for non-

> internet purposes (so no viruses/spyware etc for sure - and I am the

> only person with access to this office).

>

> Yesterday morning I came into work to find that one of my PCs did not

> power on at all. The following happened (in order):

>

> 1. Switched PSU off from back, turned it on again - no result

> 2. Unplugged and re-plugged power cable in case it was loose - no

> result

> 3. Switch power cable for another one - the PC powers on

>

> - NOTE : The "faulty" cable works on another PC - and I'm not crazy!

> =)

>

> 4. When PC powers on, get an error message saying BIOS config not set.

> Upon entering BIOS, date is 2003 etc as if someone had completely

> reset the BIOS.

> 5. Entered the basic details (date etc) and turned on PC - everything

> worked

>

> 6. Yesterday, night, tried to shut-down, but after shutting down, the

> computer powered itself on again after about 3 or 4 seconds. Tested

> and re-tested this - in the end, I waited for it to power off, and

> then turned it off from the power switch on the back of the PSU

>

> 7. Finally, this morning came in and turned it on again - system wont

> go into windows normally, or into safe mode, or into last known good

> configuration. Each time, it just reboots itself.

>

> What would be the logical order to proceed in order to correct this

> problem? My gut tells me to check out the PSU first, but I am not

> aware/sure if the PSU can be responsible for the reset command.

>

 

Follow these steps in exactly the order specified:

 

1. Replace the motherboard's battery.

 

If the battery fails, the CMOS reverts to its factory settings. These

setting could include "Boot from water fountain" or somesuch. After powering

on the computer, and finally getting it to run, the battery could retain

sufficient charge to limp along for any (relatively) short period with the

power off. That may be why conditions seem confusing.

[Guest Bob I]

Re: Cant access XP Pro normal/safe/last good config

 

While replacing the CMOS battery (as also suggested by others) please

look at the electrolitic capactitors on the motherboard for signs of

bulging, distended bottoms, or leakage.

 

abd08 wrote:

> Hi all,

>

> I have a PC at work which I did a clean install of XP Pro on a few

> weeks ago. It has been used very infrequently only by me, for non-

> internet purposes (so no viruses/spyware etc for sure - and I am the

> only person with access to this office).

>

> Yesterday morning I came into work to find that one of my PCs did not

> power on at all. The following happened (in order):

>

> 1. Switched PSU off from back, turned it on again - no result

> 2. Unplugged and re-plugged power cable in case it was loose - no

> result

> 3. Switch power cable for another one - the PC powers on

>

> - NOTE : The "faulty" cable works on another PC - and I'm not crazy!

> =)

>

> 4. When PC powers on, get an error message saying BIOS config not set.

> Upon entering BIOS, date is 2003 etc as if someone had completely

> reset the BIOS.

> 5. Entered the basic details (date etc) and turned on PC - everything

> worked

>

> 6. Yesterday, night, tried to shut-down, but after shutting down, the

> computer powered itself on again after about 3 or 4 seconds. Tested

> and re-tested this - in the end, I waited for it to power off, and

> then turned it off from the power switch on the back of the PSU

>

> 7. Finally, this morning came in and turned it on again - system wont

> go into windows normally, or into safe mode, or into last known good

> configuration. Each time, it just reboots itself.

>

> What would be the logical order to proceed in order to correct this

> problem? My gut tells me to check out the PSU first, but I am not

> aware/sure if the PSU can be responsible for the reset command.

>

> Thanks in advance,

> Raj