External drives not installing or working properly on USB

[Guest Simon]

I have a graphics workstation based around an Intel D975XBX2 motherboard with

quad core processor and 3GB RAM. USB host controllers are Intel 82801G (ICH7

Family). Only one of the five host controllers is connected to the 6 external

ports. This is listed as a USB2 enhanced host controller.

 

I am experiencing problems with a Sandisk ImageMate 12 in 1 card reader

modelSDDR-89 V4 and a Western Digital 2TB external mirror raid drive, both

USB2 peripherals.

 

Both were bought at the same time and shortly after I had installed XP SP3.

Plug and play installation of the WD drive went through most of the automated

process before indicating that the drevice had not installed correctly. No

external drive was recognised. The computer froze completely while trying to

install the Sandisk card reader.

 

I scanned the system and identified some old drivers. All relevant hardware

and XP drivers were checked and updated where necessary. BIOS was also out of

date so this was also brought up to date. No change.

 

All the USB controllers were removed via the device manager and the system

allowed to reinstall them - no change.

 

The USB root hub has been checked. 8 ports are available in total of which 6

are actually physically available. An External hub is connected to one port

and supports the keyboard and mouse. This draws 500mA. A second port connects

to a printer switch and draws from 2 to 10mA in operation. Each port is rated

at 500mA and there is no indication that too much is being drawn on any

particular port.

 

The operating system was rolled back to SP2 and the checks above repeated.

Now the Sandisk drive installs but it can take up to 5 minutes for the

operating system to recognise the four additional 'drives'. It then tries to

autoplay, even with no card in the reader. This does not cancel and can go on

for another 5 minutes.

 

The WD drive still does not install.

 

I have the same problems on a laptop, also running XP. I got the WD drive to

come up on this machine once when rolled back to SP2 but it disappeared after

rebooting and has never been seen again. This machine also uses Intel host

controllers but a slightly older chipset.

 

All the external hardware works fine under Vista (and fast too). Microsoft

say it's a hardware problem.

 

I am out of ideas.

[Guest M.I.5¾]

Re: External drives not installing or working properly on USB

 

 

"Simon" <Simon@discussions.microsoft.com> wrote in message

news:78748873-6B78-409E-90D2-74678B8947AC@microsoft.com...

>I have a graphics workstation based around an Intel D975XBX2 motherboard

>with

> quad core processor and 3GB RAM. USB host controllers are Intel 82801G

> (ICH7

> Family). Only one of the five host controllers is connected to the 6

> external

> ports. This is listed as a USB2 enhanced host controller.

>

 

This is not correct. As you have 5 host ports, you have 8 physical USB

ports (and as you note 6 are brought to the outside world). 4 of the host

ports are OHCI host ports and provide the slow and fast communication to 2

each (making 8 in all) of the physical ports (what most people call USB1).

The remaining host is a EHCI host providing high speed communication to all

8 physical ports (usually refered to as USB2). There are very good

technical reasons for this apparently cockermainy arrangement.

 

All your other symptoms sound suspiciously like the OHCI ports on either the

host or peripheral having some problem. What is not clear is: do they not

work on any port on the PC? When you say yhey work under Vista, is this on

the same or a different PC?

 

You seem to be suggesting that your problems appeared after upgrading the

SP3. I assume that you don't have the ability to restore a backup of the

SP2 system before you upgraded to SP3 (very bad and unwise move) otherwise

you would have restored it. This may sound a bit drastic, but if you have

an old or another hard disk, are you able to rebuild a windows SP2

installation, and does it work with USB? This last bit would confirm

whether the hardware was OK and if the support software drivers have become

damaged.

> I am experiencing problems with a Sandisk ImageMate 12 in 1 card reader

> modelSDDR-89 V4 and a Western Digital 2TB external mirror raid drive, both

> USB2 peripherals.

>

> Both were bought at the same time and shortly after I had installed XP

> SP3.

> Plug and play installation of the WD drive went through most of the

> automated

> process before indicating that the drevice had not installed correctly. No

> external drive was recognised. The computer froze completely while trying

> to

> install the Sandisk card reader.

>

> I scanned the system and identified some old drivers. All relevant

> hardware

> and XP drivers were checked and updated where necessary. BIOS was also out

> of

> date so this was also brought up to date. No change.

>

> All the USB controllers were removed via the device manager and the system

> allowed to reinstall them - no change.

>

> The USB root hub has been checked. 8 ports are available in total of which

> 6

> are actually physically available. An External hub is connected to one

> port

> and supports the keyboard and mouse. This draws 500mA. A second port

> connects

> to a printer switch and draws from 2 to 10mA in operation. Each port is

> rated

> at 500mA and there is no indication that too much is being drawn on any

> particular port.

>

> The operating system was rolled back to SP2 and the checks above repeated.

> Now the Sandisk drive installs but it can take up to 5 minutes for the

> operating system to recognise the four additional 'drives'. It then tries

> to

> autoplay, even with no card in the reader. This does not cancel and can go

> on

> for another 5 minutes.

>

> The WD drive still does not install.

>

> I have the same problems on a laptop, also running XP. I got the WD drive

> to

> come up on this machine once when rolled back to SP2 but it disappeared

> after

> rebooting and has never been seen again. This machine also uses Intel host

> controllers but a slightly older chipset.

>

> All the external hardware works fine under Vista (and fast too). Microsoft

> say it's a hardware problem.

>

> I am out of ideas.

[Guest Simon]

Re: External drives not installing or working properly on USB

 

Well, thanks for clarifying the setup of the USB host controllers. I am sure

that there is a good reason for running it this way but it is not terribly

transparent to a rank amateur like me.

 

I can't be absolutely certain if SP3 is the problem or not since this was

upgraded prior to trying to set up the external drives (a couple of weeks

earlier). I have rolled the system back to SP2 successfully on both the

affected machines using an existing good backup made before the upgrade. The

Sandisk card reader now works but very slowly and the WD drive not at all.

This is the case for both XP machines.

 

Vista is running on another machine and when I checked it all the external

hardware was working perfectly.

 

I think that this means one of the following.

 

1. There is a compatibility problem with the Intel hardware at some level

(which is the Microsoft position) and the solution lies at the Intel driver

level. I have contacted Intel but no reply.

 

2. There is a hardware problem with the USB system on the work station in

particular. This is still a possibility since there have been minor glitches

with the USB system before but these disappearred when I disabled the

automatic power management. None of the other tests I have done suggested

that there was a problem. The only other thing I have noted was an early

problem with a Belkin 4 x 1 USB switch which could not be made to work at all

on the workstation. The USB steadfastly refused to recognise the device. I

also got a power warning when it was connected to the laptop.

 

2. XP has not rolled back properly.

 

3. The XP installation on both machines has some problem. This is unlikely

since I recently completely rebuilt the system on the laptop.

 

4. There is a fundamental problem with both the external units. This is

unlikely or they wouldn't work on Vista.

 

On the advice of WD I have sent the 2TB mirror drive back for them to

perform some tests, just in case there is some problem. I have contacted

Intel but so far have had no response. Microsoft do not believe that there is

an XP problem.

 

Unless there is a flash of inspiration the only thing I can think of doing

is completely rebuilding these machines from the ground up to ensure that the

drivers are absolutely right.

 

Any other ideas?

 

"M.I.5¾" wrote:

>

> "Simon" <Simon@discussions.microsoft.com> wrote in message

> news:78748873-6B78-409E-90D2-74678B8947AC@microsoft.com...

> >I have a graphics workstation based around an Intel D975XBX2 motherboard

> >with

> > quad core processor and 3GB RAM. USB host controllers are Intel 82801G

> > (ICH7

> > Family). Only one of the five host controllers is connected to the 6

> > external

> > ports. This is listed as a USB2 enhanced host controller.

> >

>

> This is not correct. As you have 5 host ports, you have 8 physical USB

> ports (and as you note 6 are brought to the outside world). 4 of the host

> ports are OHCI host ports and provide the slow and fast communication to 2

> each (making 8 in all) of the physical ports (what most people call USB1).

> The remaining host is a EHCI host providing high speed communication to all

> 8 physical ports (usually refered to as USB2). There are very good

> technical reasons for this apparently cockermainy arrangement.

>

> All your other symptoms sound suspiciously like the OHCI ports on either the

> host or peripheral having some problem. What is not clear is: do they not

> work on any port on the PC? When you say yhey work under Vista, is this on

> the same or a different PC?

>

> You seem to be suggesting that your problems appeared after upgrading the

> SP3. I assume that you don't have the ability to restore a backup of the

> SP2 system before you upgraded to SP3 (very bad and unwise move) otherwise

> you would have restored it. This may sound a bit drastic, but if you have

> an old or another hard disk, are you able to rebuild a windows SP2

> installation, and does it work with USB? This last bit would confirm

> whether the hardware was OK and if the support software drivers have become

> damaged.

>

> > I am experiencing problems with a Sandisk ImageMate 12 in 1 card reader

> > modelSDDR-89 V4 and a Western Digital 2TB external mirror raid drive, both

> > USB2 peripherals.

> >

> > Both were bought at the same time and shortly after I had installed XP

> > SP3.

> > Plug and play installation of the WD drive went through most of the

> > automated

> > process before indicating that the drevice had not installed correctly. No

> > external drive was recognised. The computer froze completely while trying

> > to

> > install the Sandisk card reader.

> >

> > I scanned the system and identified some old drivers. All relevant

> > hardware

> > and XP drivers were checked and updated where necessary. BIOS was also out

> > of

> > date so this was also brought up to date. No change.

> >

> > All the USB controllers were removed via the device manager and the system

> > allowed to reinstall them - no change.

> >

> > The USB root hub has been checked. 8 ports are available in total of which

> > 6

> > are actually physically available. An External hub is connected to one

> > port

> > and supports the keyboard and mouse. This draws 500mA. A second port

> > connects

> > to a printer switch and draws from 2 to 10mA in operation. Each port is

> > rated

> > at 500mA and there is no indication that too much is being drawn on any

> > particular port.

> >

> > The operating system was rolled back to SP2 and the checks above repeated.

> > Now the Sandisk drive installs but it can take up to 5 minutes for the

> > operating system to recognise the four additional 'drives'. It then tries

> > to

> > autoplay, even with no card in the reader. This does not cancel and can go

> > on

> > for another 5 minutes.

> >

> > The WD drive still does not install.

> >

> > I have the same problems on a laptop, also running XP. I got the WD drive

> > to

> > come up on this machine once when rolled back to SP2 but it disappeared

> > after

> > rebooting and has never been seen again. This machine also uses Intel host

> > controllers but a slightly older chipset.

> >

> > All the external hardware works fine under Vista (and fast too). Microsoft

> > say it's a hardware problem.

> >

> > I am out of ideas.

>

>

>

[Guest smlunatick]

Re: External drives not installing or working properly on USB

 

On Sep 16, 12:08 pm, Simon <Si...@discussions.microsoft.com> wrote:

> Well, thanks for clarifying the setup of the USB host controllers. I am sure

> that there is a good reason for running it this way but it is not terribly

> transparent to a rank amateur like me.

>

> I can't be absolutely certain if SP3 is the problem or not since this was

> upgraded prior to trying to set up the external drives (a couple of weeks

> earlier). I have rolled the system back to SP2 successfully on both the

> affected machines using an existing good backup made before the upgrade. The

> Sandisk card reader now works but very slowly and the WD drive not at all..

> This is the case for both XP machines.

>

> Vista is running on another machine and when I checked it all the external

> hardware was working perfectly.

>

> I think that this means one of the following.

>

> 1. There is a compatibility problem with the Intel hardware at some level

> (which is the Microsoft position) and the solution lies at the Intel driver

> level. I have contacted Intel but no reply.

>

> 2. There is a hardware problem with the USB system on the work station in

> particular. This is still a possibility since there have been minor glitches

> with the USB system before but these disappearred when I disabled the

> automatic power management. None of the other tests I have done suggested

> that there was a problem. The only other thing I have noted was an early

> problem with a Belkin 4 x 1 USB switch which could not be made to work at all

> on the workstation. The USB steadfastly refused to recognise the device. I

> also got a power warning when it was connected to the laptop.

>

> 2. XP has not rolled back properly.

>

> 3. The XP installation on both machines has some problem. This is unlikely

> since I recently completely rebuilt the system on the laptop.

>

> 4. There is a fundamental problem with both the external units. This is

> unlikely or they wouldn't work on Vista.

>

> On the advice of WD I have sent the 2TB mirror drive back for them to

> perform some tests, just in case there is some problem. I have contacted

> Intel but so far have had no response. Microsoft do not believe that there is

> an XP problem.

>

> Unless there is a flash of inspiration the only thing I can think of doing

> is completely rebuilding these machines from the ground up to ensure that the

> drivers are absolutely right.

>

> Any other ideas?

>

> "M.I.5¾" wrote:

>

> > "Simon" <Si...@discussions.microsoft.com> wrote in message

> >news:78748873-6B78-409E-90D2-74678B8947AC@microsoft.com...

> > >I have a graphics workstation based around an Intel D975XBX2 motherboard

> > >with

> > > quad core processor and 3GB RAM. USB host controllers are Intel 82801G

> > > (ICH7

> > > Family). Only one of the five host controllers is connected to the 6

> > > external

> > > ports. This is listed as a USB2 enhanced host controller.

>

> > This is not correct.  As you have 5 host ports, you have 8 physical USB

> > ports (and as you note 6 are brought to the outside world).  4 of the host

> > ports are OHCI host ports and provide the slow and fast communication to 2

> > each (making 8 in all) of the physical ports (what most people call USB1).

> > The remaining host is a EHCI host providing high speed communication to all

> > 8 physical ports (usually refered to as USB2).  There are very good

> > technical reasons for this apparently cockermainy arrangement.

>

> > All your other symptoms sound suspiciously like the OHCI ports on either the

> > host or peripheral having some problem.  What is not clear is: do they not

> > work on any port on the PC?  When you say yhey work under Vista, is this on

> > the same or a different PC?

>

> > You seem to be suggesting that your problems appeared after upgrading the

> > SP3.  I assume that you don't have the ability to restore a backup of the

> > SP2 system before you upgraded to SP3 (very bad and unwise move) otherwise

> > you would have restored it.  This may sound a bit drastic, but if you have

> > an old or another hard disk, are you able to rebuild a windows SP2

> > installation, and does it work with USB?  This last bit would confirm

> > whether the hardware was OK and if the support software drivers have become

> > damaged.

>

> > > I am experiencing problems with a Sandisk ImageMate 12 in 1 card reader

> > > modelSDDR-89 V4 and a Western Digital 2TB external mirror raid drive, both

> > > USB2 peripherals.

>

> > > Both were bought at the same time and shortly after I had installed XP

> > > SP3.

> > > Plug and play installation of the WD drive went through most of the

> > > automated

> > > process before indicating that the drevice had not installed correctly. No

> > > external drive was recognised. The computer froze completely while trying

> > > to

> > > install the Sandisk card reader.

>

> > > I scanned the system and identified some old drivers. All relevant

> > > hardware

> > > and XP drivers were checked and updated where necessary. BIOS was also out

> > > of

> > > date so this was also brought up to date. No change.

>

> > > All the USB controllers were removed via the device manager and the system

> > > allowed to reinstall them - no change.

>

> > > The USB root hub has been checked. 8 ports are available in total of which

> > > 6

> > > are actually physically available. An External hub is connected to one

> > > port

> > > and supports the keyboard and mouse. This draws 500mA. A second port

> > > connects

> > > to a printer switch and draws from 2 to 10mA in operation. Each port is

> > > rated

> > > at 500mA and there is no indication that too much is being drawn on any

> > > particular port.

>

> > > The operating system was rolled back to SP2 and the checks above repeated.

> > > Now the Sandisk drive installs but it can take up to 5 minutes for the

> > > operating system to recognise the four additional 'drives'. It then tries

> > > to

> > > autoplay, even with no card in the reader. This does not cancel and can go

> > > on

> > > for another 5 minutes.

>

> > > The WD drive still does not install.

>

> > > I have the same problems on a laptop, also running XP. I got the WD drive

> > > to

> > > come up on this machine once when rolled back to SP2 but it disappeared

> > > after

> > > rebooting and has never been seen again. This machine also uses Intel host

> > > controllers but a slightly older chipset.

>

> > > All the external hardware works fine under Vista (and fast too). Microsoft

> > > say it's a hardware problem.

>

> > > I am out of ideas.

 

I am using another model of Intel motherboard and SP3. The problem is

not with either XP, SP3 or the hardware. You seem to have a conflict

with some settings. Locate USBDLM and you should find another web

page to help in fixing "most" USB external drive problems.

[Guest M.I.5¾]

Re: External drives not installing or working properly on USB

 

 

"Simon" <Simon@discussions.microsoft.com> wrote in message

news:5F85C8A3-16BC-44C5-9520-DC3127C965B4@microsoft.com...

> Well, thanks for clarifying the setup of the USB host controllers. I am

> sure

> that there is a good reason for running it this way but it is not terribly

> transparent to a rank amateur like me.

>

 

Oh it catches many people,

> I can't be absolutely certain if SP3 is the problem or not since this was

> upgraded prior to trying to set up the external drives (a couple of weeks

> earlier). I have rolled the system back to SP2 successfully on both the

> affected machines using an existing good backup made before the upgrade.

> The

> Sandisk card reader now works but very slowly and the WD drive not at all.

> This is the case for both XP machines.

>

> Vista is running on another machine and when I checked it all the external

> hardware was working perfectly.

>

 

OK. That means that there are still problems on the first machine. What is

puzzling is that you said that it doesn't work properly on another XP PC.

Did before? Tne one thing you could try doing is a repair install of XP

(not a full install). And for Pete's sake back the disc up before you do it

(in fact back it before you do anything). That way you can always return to

the position you were in if anthing goes wrong.

> I think that this means one of the following.

>

> 1. There is a compatibility problem with the Intel hardware at some level

> (which is the Microsoft position) and the solution lies at the Intel

> driver

> level. I have contacted Intel but no reply.

>

 

Since I have to assume that it worked OK before you installed SP3, it seems

unlikely to be the hardware. It may be that something that SP3 did has not

undone properly when you removed it.

> 2. There is a hardware problem with the USB system on the work station in

> particular. This is still a possibility since there have been minor

> glitches

> with the USB system before but these disappearred when I disabled the

> automatic power management. None of the other tests I have done suggested

> that there was a problem. The only other thing I have noted was an early

> problem with a Belkin 4 x 1 USB switch which could not be made to work at

> all

> on the workstation. The USB steadfastly refused to recognise the device. I

> also got a power warning when it was connected to the laptop.

>

 

That sounds like it could be a faulty hub. I've got one of those, but mine

can be fixed by a bit of percussive maintenance*. However, having said

that, did you check whether the hub had installed as an unkown device?

 

* Percussive maintenance: Whacking 7 bells out of it until it works.

> 2. XP has not rolled back properly.

>

 

This is my number one suspect. That it worked before you applied SP3 is

strong evidence.

> 3. The XP installation on both machines has some problem. This is unlikely

> since I recently completely rebuilt the system on the laptop.

>

 

That's the bit that puzzles me.

> 4. There is a fundamental problem with both the external units. This is

> unlikely or they wouldn't work on Vista.

>

 

That is a perfectly reasonable conclusion.

> On the advice of WD I have sent the 2TB mirror drive back for them to

> perform some tests, just in case there is some problem. I have contacted

> Intel but so far have had no response. Microsoft do not believe that there

> is

> an XP problem.

>

 

Microsoft rarely do.

> Unless there is a flash of inspiration the only thing I can think of doing

> is completely rebuilding these machines from the ground up to ensure that

> the

> drivers are absolutely right.

>

 

If there is no problem with the hardware, that should certainly solve the

problem. However, it is a drastic step, but there does become a point where

the gains outweigh the loses. Are you able follow my suggestion of

performing the rebuild on another disk drive? That at least would tell you

if you are barking up the right tree.

> Any other ideas?

>

> "M.I.5¾" wrote:

>

>>

>> "Simon" <Simon@discussions.microsoft.com> wrote in message

>> news:78748873-6B78-409E-90D2-74678B8947AC@microsoft.com...

>> >I have a graphics workstation based around an Intel D975XBX2 motherboard

>> >with

>> > quad core processor and 3GB RAM. USB host controllers are Intel 82801G

>> > (ICH7

>> > Family). Only one of the five host controllers is connected to the 6

>> > external

>> > ports. This is listed as a USB2 enhanced host controller.

>> >

>>

>> This is not correct. As you have 5 host ports, you have 8 physical USB

>> ports (and as you note 6 are brought to the outside world). 4 of the

>> host

>> ports are OHCI host ports and provide the slow and fast communication to

>> 2

>> each (making 8 in all) of the physical ports (what most people call

>> USB1).

>> The remaining host is a EHCI host providing high speed communication to

>> all

>> 8 physical ports (usually refered to as USB2). There are very good

>> technical reasons for this apparently cockermainy arrangement.

>>

>> All your other symptoms sound suspiciously like the OHCI ports on either

>> the

>> host or peripheral having some problem. What is not clear is: do they

>> not

>> work on any port on the PC? When you say yhey work under Vista, is this

>> on

>> the same or a different PC?

>>

>> You seem to be suggesting that your problems appeared after upgrading the

>> SP3. I assume that you don't have the ability to restore a backup of the

>> SP2 system before you upgraded to SP3 (very bad and unwise move)

>> otherwise

>> you would have restored it. This may sound a bit drastic, but if you

>> have

>> an old or another hard disk, are you able to rebuild a windows SP2

>> installation, and does it work with USB? This last bit would confirm

>> whether the hardware was OK and if the support software drivers have

>> become

>> damaged.

>>

>> > I am experiencing problems with a Sandisk ImageMate 12 in 1 card reader

>> > modelSDDR-89 V4 and a Western Digital 2TB external mirror raid drive,

>> > both

>> > USB2 peripherals.

>> >

>> > Both were bought at the same time and shortly after I had installed XP

>> > SP3.

>> > Plug and play installation of the WD drive went through most of the

>> > automated

>> > process before indicating that the drevice had not installed correctly.

>> > No

>> > external drive was recognised. The computer froze completely while

>> > trying

>> > to

>> > install the Sandisk card reader.

>> >

>> > I scanned the system and identified some old drivers. All relevant

>> > hardware

>> > and XP drivers were checked and updated where necessary. BIOS was also

>> > out

>> > of

>> > date so this was also brought up to date. No change.

>> >

>> > All the USB controllers were removed via the device manager and the

>> > system

>> > allowed to reinstall them - no change.

>> >

>> > The USB root hub has been checked. 8 ports are available in total of

>> > which

>> > 6

>> > are actually physically available. An External hub is connected to one

>> > port

>> > and supports the keyboard and mouse. This draws 500mA. A second port

>> > connects

>> > to a printer switch and draws from 2 to 10mA in operation. Each port is

>> > rated

>> > at 500mA and there is no indication that too much is being drawn on any

>> > particular port.

>> >

>> > The operating system was rolled back to SP2 and the checks above

>> > repeated.

>> > Now the Sandisk drive installs but it can take up to 5 minutes for the

>> > operating system to recognise the four additional 'drives'. It then

>> > tries

>> > to

>> > autoplay, even with no card in the reader. This does not cancel and can

>> > go

>> > on

>> > for another 5 minutes.

>> >

>> > The WD drive still does not install.

>> >

>> > I have the same problems on a laptop, also running XP. I got the WD

>> > drive

>> > to

>> > come up on this machine once when rolled back to SP2 but it disappeared

>> > after

>> > rebooting and has never been seen again. This machine also uses Intel

>> > host

>> > controllers but a slightly older chipset.

>> >

>> > All the external hardware works fine under Vista (and fast too).

>> > Microsoft

>> > say it's a hardware problem.

>> >

>> > I am out of ideas.

>>

>>

>>