Guest DiDi Posted October 19, 2008 Posted October 19, 2008 Memory parity system halted on startup. What is failing in this old (9 year old) Dell XPST 450. I would like to backup all data. Then start Win 98se all over clean and go on from there. But ....over the past year, before I got my new machine. Every once in a while I get Memory Parity detected, system halted. Then I reboot and everything is ok. Any ideas for next steps?
Guest philo Posted October 19, 2008 Posted October 19, 2008 Re: memory parity "DiDi" <Iam@Shangrila.net> wrote in message news:enPMushMJHA.1304@TK2MSFTNGP02.phx.gbl... > Memory parity system halted on startup. What is failing in this old (9 > year old) Dell > XPST 450. I would like to backup all data. Then start Win 98se all over > clean and go > on from there. But ....over the past year, before I got my new machine. > Every once > in a while I get Memory Parity detected, system halted. Then I reboot and > everything > is ok. Any ideas for next steps? > > Open the case and check your RAM make sure the connections are good and clean. Try reseating it. Also run a RAM test such as memtest86
Guest DiDi Posted October 19, 2008 Posted October 19, 2008 Re: memory parity I vaguely remember that when I added my last stick of Ram it was higher than the one before it. Someone told me I should have switched the places of those two so that the highest came first and then the lower. Can I switch them now or just clean them and seat them? I ran a memory check a couple of months ago and it was ok and this has been going on for over a year. Do I still have to do another one? "philo" <philo@privacy.net> wrote in message news:u1%23O4CiMJHA.4248@TK2MSFTNGP03.phx.gbl... > > "DiDi" <Iam@Shangrila.net> wrote in message > news:enPMushMJHA.1304@TK2MSFTNGP02.phx.gbl... > > Memory parity system halted on startup. What is failing in this old (9 > > year old) Dell > > XPST 450. I would like to backup all data. Then start Win 98se all over > > clean and go > > on from there. But ....over the past year, before I got my new machine. > > Every once > > in a while I get Memory Parity detected, system halted. Then I reboot and > > everything > > is ok. Any ideas for next steps? > > > > > > > Open the case and check your RAM > > make sure the connections are good and clean. > > Try reseating it. > > Also run a RAM test such as memtest86 > >
Guest philo Posted October 19, 2008 Posted October 19, 2008 Re: memory parity "DiDi" <Iam@Shangrila.net> wrote in message news:%23slvSLiMJHA.2044@TK2MSFTNGP04.phx.gbl... >I vaguely remember that when I added my last stick of Ram it was higher >than the one > before it. Someone told me I should have switched the places of those two > so that the > highest came first and then the lower. Can I switch them now or just clean > them and > seat them? I ran a memory check a couple of months ago and it was ok and > this has > been going on for over a year. Do I still have to do another one? > Just because the RAM passed a test... there still could be a problem. I don't know if it will make any difference switching the sticks around...you can try it if you want. I'd run it on just your original stick for a while and see what happens... If no problems , then just try it on the newer stick. The problem could be with one of them... or the problem could be they simply are not compatable with each other > "philo" <philo@privacy.net> wrote in message > news:u1%23O4CiMJHA.4248@TK2MSFTNGP03.phx.gbl... >> >> "DiDi" <Iam@Shangrila.net> wrote in message >> news:enPMushMJHA.1304@TK2MSFTNGP02.phx.gbl... >> > Memory parity system halted on startup. What is failing in this old (9 >> > year old) Dell >> > XPST 450. I would like to backup all data. Then start Win 98se all over >> > clean and go >> > on from there. But ....over the past year, before I got my new >> > machine. >> > Every once >> > in a while I get Memory Parity detected, system halted. Then I reboot >> > and >> > everything >> > is ok. Any ideas for next steps? >> > >> > >> >> >> Open the case and check your RAM >> >> make sure the connections are good and clean. >> >> Try reseating it. >> >> Also run a RAM test such as memtest86 >> >> > >
Guest DiDi Posted October 19, 2008 Posted October 19, 2008 Re: memory parity I guess that means there definitely is a problem. I'll get to work. Thank you , philo. "philo" <philo@privacy.net> wrote in message news:uh0t5DjMJHA.1160@TK2MSFTNGP04.phx.gbl... > > "DiDi" <Iam@Shangrila.net> wrote in message > news:%23slvSLiMJHA.2044@TK2MSFTNGP04.phx.gbl... > >I vaguely remember that when I added my last stick of Ram it was higher > >than the one > > before it. Someone told me I should have switched the places of those two > > so that the > > highest came first and then the lower. Can I switch them now or just clean > > them and > > seat them? I ran a memory check a couple of months ago and it was ok and > > this has > > been going on for over a year. Do I still have to do another one? > > > > Just because the RAM passed a test... > there still could be a problem. > > I don't know if it will make any difference switching the sticks > around...you can try it if you want. > > I'd run it on just your original stick for a while and see what happens... > > If no problems , then just try it on the newer stick. > > > The problem could be with one of them... > or the problem could be they simply are not compatable with each other > > > > "philo" <philo@privacy.net> wrote in message > > news:u1%23O4CiMJHA.4248@TK2MSFTNGP03.phx.gbl... > >> > >> "DiDi" <Iam@Shangrila.net> wrote in message > >> news:enPMushMJHA.1304@TK2MSFTNGP02.phx.gbl... > >> > Memory parity system halted on startup. What is failing in this old (9 > >> > year old) Dell > >> > XPST 450. I would like to backup all data. Then start Win 98se all over > >> > clean and go > >> > on from there. But ....over the past year, before I got my new > >> > machine. > >> > Every once > >> > in a while I get Memory Parity detected, system halted. Then I reboot > >> > and > >> > everything > >> > is ok. Any ideas for next steps? > >> > > >> > > >> > >> > >> Open the case and check your RAM > >> > >> make sure the connections are good and clean. > >> > >> Try reseating it. > >> > >> Also run a RAM test such as memtest86 > >> > >> > > > > > >
Guest philo Posted October 19, 2008 Posted October 19, 2008 Re: memory parity "DiDi" <Iam@Shangrila.net> wrote in message news:%23AnsmLjMJHA.2348@TK2MSFTNGP05.phx.gbl... >I guess that means there definitely is a problem. I'll get to work. Thank >you , OK I'd probably just run it on one stick at a time and see what happens > "philo" <philo@privacy.net> wrote in message > news:uh0t5DjMJHA.1160@TK2MSFTNGP04.phx.gbl... >> >> "DiDi" <Iam@Shangrila.net> wrote in message >> news:%23slvSLiMJHA.2044@TK2MSFTNGP04.phx.gbl... >> >I vaguely remember that when I added my last stick of Ram it was higher >> >than the one >> > before it. Someone told me I should have switched the places of those >> > two >> > so that the >> > highest came first and then the lower. Can I switch them now or just >> > clean >> > them and >> > seat them? I ran a memory check a couple of months ago and it was ok >> > and >> > this has >> > been going on for over a year. Do I still have to do another one? >> > >> >> Just because the RAM passed a test... >> there still could be a problem. >> >> I don't know if it will make any difference switching the sticks >> around...you can try it if you want. >> >> I'd run it on just your original stick for a while and see what >> happens... >> >> If no problems , then just try it on the newer stick. >> >> >> The problem could be with one of them... >> or the problem could be they simply are not compatable with each other >> >> >> > "philo" <philo@privacy.net> wrote in message >> > news:u1%23O4CiMJHA.4248@TK2MSFTNGP03.phx.gbl... >> >> >> >> "DiDi" <Iam@Shangrila.net> wrote in message >> >> news:enPMushMJHA.1304@TK2MSFTNGP02.phx.gbl... >> >> > Memory parity system halted on startup. What is failing in this old >> >> > (9 >> >> > year old) Dell >> >> > XPST 450. I would like to backup all data. Then start Win 98se all >> >> > over >> >> > clean and go >> >> > on from there. But ....over the past year, before I got my new >> >> > machine. >> >> > Every once >> >> > in a while I get Memory Parity detected, system halted. Then I >> >> > reboot >> >> > and >> >> > everything >> >> > is ok. Any ideas for next steps? >> >> > >> >> > >> >> >> >> >> >> Open the case and check your RAM >> >> >> >> make sure the connections are good and clean. >> >> >> >> Try reseating it. >> >> >> >> Also run a RAM test such as memtest86 >> >> >> >> >> > >> > >> >> > >
Guest Jeff Richards Posted October 20, 2008 Posted October 20, 2008 Re: memory parity The memory parity error is a hardware failure somewhere in the memory (RAM) system. It's not unusual for memory to be a bit flaky when it's cold, and then operate perfectly when everything is warmed up - it might not even be due to the memory, but other components (such as a power supply) that need to be warmed up a bit to run properly. If the problem is only occurring at first startup then you can probably live with it by letting the machine run for a while before starting to boot, but if it starts happening when you are using the machine you will have to address the problem. Note that an error caused by cold components is probably not going to show up in a RAM testing program - by the time you get the program up and running things are warmed up enough for the problem to disappear. -- Jeff Richards MS MVP (Windows - Shell/User) "DiDi" <Iam@Shangrila.net> wrote in message news:enPMushMJHA.1304@TK2MSFTNGP02.phx.gbl... > Memory parity system halted on startup. What is failing in this old (9 > year old) Dell > XPST 450. I would like to backup all data. Then start Win 98se all over > clean and go > on from there. But ....over the past year, before I got my new machine. > Every once > in a while I get Memory Parity detected, system halted. Then I reboot and > everything > is ok. Any ideas for next steps? > >
Guest DiDi Posted October 21, 2008 Posted October 21, 2008 Re: memory parity Thank you. "Jeff Richards" <JRichards@msn.com.au> wrote in message news:%23xKTnMmMJHA.5692@TK2MSFTNGP04.phx.gbl... > The memory parity error is a hardware failure somewhere in the memory > (RAM) system. It's not unusual for memory to be a bit flaky when it's > cold, and then operate perfectly when everything is warmed up - it might > not even be due to the memory, but other components (such as a power > supply) that need to be warmed up a bit to run properly. If the problem > is only occurring at first startup then you can probably live with it by > letting the machine run for a while before starting to boot, but if it > starts happening when you are using the machine you will have to address > the problem. Note that an error caused by cold components is probably not > going to show up in a RAM testing program - by the time you get the > program up and running things are warmed up enough for the problem to > disappear. > -- > Jeff Richards > MS MVP (Windows - Shell/User) > "DiDi" <Iam@Shangrila.net> wrote in message > news:enPMushMJHA.1304@TK2MSFTNGP02.phx.gbl... >> Memory parity system halted on startup. What is failing in this old (9 >> year old) Dell >> XPST 450. I would like to backup all data. Then start Win 98se all over >> clean and go >> on from there. But ....over the past year, before I got my new machine. >> Every once >> in a while I get Memory Parity detected, system halted. Then I reboot and >> everything >> is ok. Any ideas for next steps? >> >> > >
Guest J. P. Gilliver (John) Posted October 21, 2008 Posted October 21, 2008 Re: memory parity In message <#xKTnMmMJHA.5692@TK2MSFTNGP04.phx.gbl>, Jeff Richards <JRichards@msn.com.au> writes >The memory parity error is a hardware failure somewhere in the memory (RAM) >system. It's not unusual for memory to be a bit flaky when it's cold, and >then operate perfectly when everything is warmed up - it might not even be >due to the memory, but other components (such as a power supply) that need >to be warmed up a bit to run properly. If the problem is only occurring at >first startup then you can probably live with it by letting the machine run >for a while before starting to boot, but if it starts happening when you are If you're wondering how to do that: press the Pause key at some point early in the boot process, then the enter key (which cancels the Pause key) when you decide it's had long enough. >using the machine you will have to address the problem. Note that an error >caused by cold components is probably not going to show up in a RAM testing >program - by the time you get the program up and running things are warmed >up enough for the problem to disappear. -- J. P. Gilliver. UMRA: 1960/<1985 MB++G.5AL(+++)IS-P--Ch+(p)Ar+T[?]H+Sh0!:`)DNAf ** http://www.soft255.demon.co.uk/G6JPG-PC/JPGminPC.htm for thoughts on PCs. ** "Bother,"saidPoohwhenhisspacebarrefusedtowork.
Recommended Posts