Cloned hard drive difficulties

[Guest Moxieman]

I bought a used Dell Inspiron 1000 laptop running XP home edition, SP3. I do

NOT have either installation CD or rescue CD for it. The hard drive has 3

partitions, a 16-meg (I assume it is boot), a C: drive, and a G: drive, which

has the Dell rescue files. The C: drive is marked Healthy (system).

 

The hard drive is dying, so I bought a new hard drive and used Norton Ghost

2003 to clone it onto a new one. I could not assign the equivalent partition

on the new hard disc the C: letter because the old, cloned partition's C:

drive had that letter. Also, I could make that equivalent partition “Healthy”

but not “system.” I understand that I cannot have two partitions with the

same letter, and cannot have two partitions marked “system” at the same time.

 

I swapped out the drives. When I tried to boot, of course, I got a message

of “error loading operating system.” I can boot into Dell Diagnostics and the

hardware checks out fine, but Dell Diagnostics doesn't allow me to change

partition letters or make a partition a “system” partition.

 

1. How do I assign the new partition the C: partition letter without a

rescue or install CD?

 

2. How do I mark the new partition as “system” and not just “healthy?”

 

I have the old hard drive and can always put it in and run disk management,

but that still leaves me with the problems of assigning the drive letter and

making it “system.”

 

Also, the new hard drive is 250 gigabytes, but the BIOS shows it as 137

gigabytes. Is that related to the problem?

 

Thanks,

 

Moxieman

[Guest Pegasus \(MVP\)]

Re: Cloned hard drive difficulties

 

See below.

 

"Moxieman" <Moxieman@discussions.microsoft.com> wrote in message

news:D93820E6-08F1-491C-A832-87F9D75AF297@microsoft.com...

>I bought a used Dell Inspiron 1000 laptop running XP home edition, SP3. I

>do

> NOT have either installation CD or rescue CD for it. The hard drive has 3

> partitions, a 16-meg (I assume it is boot), a C: drive, and a G: drive,

> which

> has the Dell rescue files. The C: drive is marked Healthy (system).

>

> The hard drive is dying, so I bought a new hard drive and used Norton

> Ghost

> 2003 to clone it onto a new one. I could not assign the equivalent

> partition

> on the new hard disc the C: letter because the old, cloned partition's C:

> drive had that letter.

*** Drive letter assignments as seen during the cloning process are

*** irrelevant. It's the assignment on the final Windows installation

*** that counts.

> Also, I could make that equivalent partition "Healthy"

> but not "system."

*** You don't make it "healthty" or "system" but you must mark

*** it "active" if you want to boot from it.

>I understand that I cannot have two partitions with the

> same letter, and cannot have two partitions marked "system" at

> the same time.

>

> I swapped out the drives. When I tried to boot, of course, I got a message

> of "error loading operating system." I can boot into Dell Diagnostics and

> the

> hardware checks out fine, but Dell Diagnostics doesn't allow me to change

> partition letters or make a partition a "system" partition.

*** See above about the "system partition".

> 1. How do I assign the new partition the C: partition letter without a

> rescue or install CD?

*** There may be no need to change anything.

> 2. How do I mark the new partition as "system" and not just "healthy?"

*** You mark it active. Here is one way to do it:

*** - Boot the machine with a Win98 boot diskette from

*** http://www.bootdisk.com.

*** - Run fdisk.exe.

*** - Mark the first partition as "active".

> I have the old hard drive and can always put it in and run disk

> management,

> but that still leaves me with the problems of assigning the drive letter

> and

> making it "system."

*** If you can connect both disks at the same time then you can

*** mark the first partition on the new disk as "active" in the Disk

*** Manager.

> Also, the new hard drive is 250 gigabytes, but the BIOS shows it as 137

> gigabytes. Is that related to the problem?

*** No, it isn't, but I'm not sure whether Windows XP will be subject

*** to the same limitation.

> Thanks,

>

> Moxieman

[Guest philo]

Re: Cloned hard drive difficulties

 

 

"Moxieman" <Moxieman@discussions.microsoft.com> wrote in message

news:D93820E6-08F1-491C-A832-87F9D75AF297@microsoft.com...

> I bought a used Dell Inspiron 1000 laptop running XP home edition, SP3. I

do

> NOT have either installation CD or rescue CD for it. The hard drive has 3

> partitions, a 16-meg (I assume it is boot), a C: drive, and a G: drive,

which

> has the Dell rescue files. The C: drive is marked Healthy (system).

>

> The hard drive is dying, so I bought a new hard drive and used Norton

Ghost

> 2003 to clone it onto a new one. I could not assign the equivalent

partition

> on the new hard disc the C: letter because the old, cloned partition's C:

> drive had that letter. Also, I could make that equivalent partition

"Healthy"

> but not "system." I understand that I cannot have two partitions with the

> same letter, and cannot have two partitions marked "system" at the same

time.

>

> I swapped out the drives. When I tried to boot, of course, I got a message

> of "error loading operating system." I can boot into Dell Diagnostics and

the

> hardware checks out fine, but Dell Diagnostics doesn't allow me to change

> partition letters or make a partition a "system" partition.

>

> 1. How do I assign the new partition the C: partition letter without a

> rescue or install CD?

>

> 2. How do I mark the new partition as "system" and not just "healthy?"

>

> I have the old hard drive and can always put it in and run disk

management,

> but that still leaves me with the problems of assigning the drive letter

and

> making it "system."

>

> Also, the new hard drive is 250 gigabytes, but the BIOS shows it as 137

> gigabytes. Is that related to the problem?

>

> Thanks,

>

> Moxieman

 

 

After you make the clone you MUST disconnect the cloned drive and put it in

place of your original.

 

If you bootup once the clone has been made, but leave the drive attached

it willbe reassigned to the wrong drive letter.

 

You will need to reclone the entire drive to get it to work

[Guest Moxieman]

Re: Cloned hard drive difficulties

 

 

Thanks, but still no luck. I did swap out the drives and boot failed. I did

notice something unusual, however, and wonder if this is the problem

 

My first partition is, of course, the EISA format 16 meg partition that is

used (I assume) for booting. After doing some research on line, I noted that

while most EISA partitions do not have a drive letter and cannot be assigned

one, the EISA partition on my original Dell hard disk DOES have a drive

letter assigned to it. It is labelled as the "G:" drive.

 

On the cloned drive, the EISA format first partition does NOT have a drive

letter assigned to it.

 

Could that be the problem?

 

Thanks.

 

"philo" wrote:

>

> "Moxieman" <Moxieman@discussions.microsoft.com> wrote in message

> news:D93820E6-08F1-491C-A832-87F9D75AF297@microsoft.com...

> > I bought a used Dell Inspiron 1000 laptop running XP home edition, SP3. I

> do

> > NOT have either installation CD or rescue CD for it. The hard drive has 3

> > partitions, a 16-meg (I assume it is boot), a C: drive, and a G: drive,

> which

> > has the Dell rescue files. The C: drive is marked Healthy (system).

> >

> > The hard drive is dying, so I bought a new hard drive and used Norton

> Ghost

> > 2003 to clone it onto a new one. I could not assign the equivalent

> partition

> > on the new hard disc the C: letter because the old, cloned partition's C:

> > drive had that letter. Also, I could make that equivalent partition

> "Healthy"

> > but not "system." I understand that I cannot have two partitions with the

> > same letter, and cannot have two partitions marked "system" at the same

> time.

> >

> > I swapped out the drives. When I tried to boot, of course, I got a message

> > of "error loading operating system." I can boot into Dell Diagnostics and

> the

> > hardware checks out fine, but Dell Diagnostics doesn't allow me to change

> > partition letters or make a partition a "system" partition.

> >

> > 1. How do I assign the new partition the C: partition letter without a

> > rescue or install CD?

> >

> > 2. How do I mark the new partition as "system" and not just "healthy?"

> >

> > I have the old hard drive and can always put it in and run disk

> management,

> > but that still leaves me with the problems of assigning the drive letter

> and

> > making it "system."

> >

> > Also, the new hard drive is 250 gigabytes, but the BIOS shows it as 137

> > gigabytes. Is that related to the problem?

> >

> > Thanks,

> >

> > Moxieman

>

>

> After you make the clone you MUST disconnect the cloned drive and put it in

> place of your original.

>

> If you bootup once the clone has been made, but leave the drive attached

> it willbe reassigned to the wrong drive letter.

>

> You will need to reclone the entire drive to get it to work

>

>

>

[Guest R. McCarty]

Re: Cloned hard drive difficulties

 

If you have Norton Ghost, you're going to great lengths to preserve

the recovery structure. It might be better to save the original drive as

is and reconfigure the clone. Since you have "Imaging" capability you

could just remove the Boot/Redirect and recovery partitions. Then

use a Disk Management tool ( Acronis ) and make the C:\ active and

expand the volume to use 100% of the physical drive. Once done &

bootable - just Ghost to image the Factory state. From that point

forward a recovery would be done with the Ghost Image set.

 

"Moxieman" <Moxieman@discussions.microsoft.com> wrote in message

news:998E1EFB-06B7-496B-97D8-CD12A57187C1@microsoft.com...

>

> Thanks, but still no luck. I did swap out the drives and boot failed. I

> did

> notice something unusual, however, and wonder if this is the problem

>

> My first partition is, of course, the EISA format 16 meg partition that is

> used (I assume) for booting. After doing some research on line, I noted

> that

> while most EISA partitions do not have a drive letter and cannot be

> assigned

> one, the EISA partition on my original Dell hard disk DOES have a drive

> letter assigned to it. It is labelled as the "G:" drive.

>

> On the cloned drive, the EISA format first partition does NOT have a drive

> letter assigned to it.

>

> Could that be the problem?

>

> Thanks.

>

> "philo" wrote:

>

>>

>> "Moxieman" <Moxieman@discussions.microsoft.com> wrote in message

>> news:D93820E6-08F1-491C-A832-87F9D75AF297@microsoft.com...

>> > I bought a used Dell Inspiron 1000 laptop running XP home edition, SP3.

>> > I

>> do

>> > NOT have either installation CD or rescue CD for it. The hard drive has

>> > 3

>> > partitions, a 16-meg (I assume it is boot), a C: drive, and a G: drive,

>> which

>> > has the Dell rescue files. The C: drive is marked Healthy (system).

>> >

>> > The hard drive is dying, so I bought a new hard drive and used Norton

>> Ghost

>> > 2003 to clone it onto a new one. I could not assign the equivalent

>> partition

>> > on the new hard disc the C: letter because the old, cloned partition's

>> > C:

>> > drive had that letter. Also, I could make that equivalent partition

>> "Healthy"

>> > but not "system." I understand that I cannot have two partitions with

>> > the

>> > same letter, and cannot have two partitions marked "system" at the same

>> time.

>> >

>> > I swapped out the drives. When I tried to boot, of course, I got a

>> > message

>> > of "error loading operating system." I can boot into Dell Diagnostics

>> > and

>> the

>> > hardware checks out fine, but Dell Diagnostics doesn't allow me to

>> > change

>> > partition letters or make a partition a "system" partition.

>> >

>> > 1. How do I assign the new partition the C: partition letter without a

>> > rescue or install CD?

>> >

>> > 2. How do I mark the new partition as "system" and not just "healthy?"

>> >

>> > I have the old hard drive and can always put it in and run disk

>> management,

>> > but that still leaves me with the problems of assigning the drive

>> > letter

>> and

>> > making it "system."

>> >

>> > Also, the new hard drive is 250 gigabytes, but the BIOS shows it as 137

>> > gigabytes. Is that related to the problem?

>> >

>> > Thanks,

>> >

>> > Moxieman

>>

>>

>> After you make the clone you MUST disconnect the cloned drive and put it

>> in

>> place of your original.

>>

>> If you bootup once the clone has been made, but leave the drive attached

>> it willbe reassigned to the wrong drive letter.

>>

>> You will need to reclone the entire drive to get it to work

>>

>>

>>