Guest UHHG_Network_Guy Posted December 4, 2007 Posted December 4, 2007 I am having trouble syncing my DC's with an outside time source and an inside time source. I have used the following command with no luck: w32tm /config /manualpeerlist:NTP_server_IP_Address,0x08 /syncfromflags:MANUAL For NTP_server_IP_Address I used the following entries: time.windows.com, pool.ntp.org, & time.nist.gov. After restarting the time service, I would run the command, w32tm /resync and I get the following the error message: "The computer did not resync because no time data was available." I then wen to a member server and ran the same commands except they work on the member server. So I then tried to sync the DC's with the member server but I am getting the same message, "The computer did not resync because no time data was available."
Guest Meinolf Weber Posted December 4, 2007 Posted December 4, 2007 Re: Time Sync from a DC Hello UHHG_Network_Guy, Do you run a firewall? Check that the port is open for 123 UDP. Best regards Meinolf Weber Disclaimer: This posting is provided "AS IS" with no warranties, and confers no rights. ** Please do NOT email, only reply to Newsgroups ** HELP us help YOU!!! http://www.dts-l.org/goodpost.htm > I am having trouble syncing my DC's with an outside time source and an > inside > time source. I have used the following command with no luck: > w32tm /config /manualpeerlist:NTP_server_IP_Address,0x08 > /syncfromflags:MANUAL > For NTP_server_IP_Address I used the following entries: > time.windows.com, > pool.ntp.org, & time.nist.gov. After restarting the time service, I > would > run the command, w32tm /resync and I get the following the error > message: > "The computer did not resync because no time data was available." > I then wen to a member server and ran the same commands except they > work on the member server. So I then tried to sync the DC's with the > member server but I am getting the same message, "The computer did not > resync because no time data was available." >
Guest UHHG_Network_Guy Posted December 4, 2007 Posted December 4, 2007 Re: Time Sync from a DC Unfortunately, I have already checked that. I have configured a member server to go out on the internet and sync its time. and it works. I am able to sync the member server with the same sites that the DC's are not. So when I attempted to sync my DC's with the member server, the sync fails on the member server. Any ideas? "Meinolf Weber" wrote: > Hello UHHG_Network_Guy, > > Do you run a firewall? Check that the port is open for 123 UDP. > > Best regards > > Meinolf Weber > Disclaimer: This posting is provided "AS IS" with no warranties, and confers > no rights. > ** Please do NOT email, only reply to Newsgroups > ** HELP us help YOU!!! http://www.dts-l.org/goodpost.htm > > > I am having trouble syncing my DC's with an outside time source and an > > inside > > time source. I have used the following command with no luck: > > w32tm /config /manualpeerlist:NTP_server_IP_Address,0x08 > > /syncfromflags:MANUAL > > For NTP_server_IP_Address I used the following entries: > > time.windows.com, > > pool.ntp.org, & time.nist.gov. After restarting the time service, I > > would > > run the command, w32tm /resync and I get the following the error > > message: > > "The computer did not resync because no time data was available." > > I then wen to a member server and ran the same commands except they > > work on the member server. So I then tried to sync the DC's with the > > member server but I am getting the same message, "The computer did not > > resync because no time data was available." > > > > >
Recommended Posts