Dual NIC education

[Guest pvong]

I'm a newbie so please explain.

 

I got a couple of servers running running w2003 with dual NICs. I'm trying

to figure out how to use the dual NICs.

1) Do you guys assign different IPs to each NIC? If so, do you make two

different A records for the same server except with two different IPs?

2) Even though each NIC has it's own MAC address, can I assign them with the

same IP number?

 

Basically, I'm trying to see if can use both NICs at the same time. I don't

understand if some request information to an IP and I have 2 NICs with the

same IP, will the request happen twice? This would create overhead.

 

Please educate me like I'm a newbie who just started working with this

stuff.

 

Thanks!

Phil

[Guest Rich]

RE: Dual NIC education

 

Depending on the manufacturer what it's called will be different, but you can

set up a virtual NIC, which is really just the two NICs teamed together for

load balancing or fault tolerance, whichever you prefer. then you just put

the IP on the virtual NIC.

the info will either load balance between the 2 NICs or just go to the one

(if going with fault tolerance).

 

 

"pvong" wrote:

> I'm a newbie so please explain.

>

> I got a couple of servers running running w2003 with dual NICs. I'm trying

> to figure out how to use the dual NICs.

> 1) Do you guys assign different IPs to each NIC? If so, do you make two

> different A records for the same server except with two different IPs?

> 2) Even though each NIC has it's own MAC address, can I assign them with the

> same IP number?

>

> Basically, I'm trying to see if can use both NICs at the same time. I don't

> understand if some request information to an IP and I have 2 NICs with the

> same IP, will the request happen twice? This would create overhead.

>

> Please educate me like I'm a newbie who just started working with this

> stuff.

>

> Thanks!

> Phil

>

>

>

[Guest Chris D]

Re: Dual NIC education

 

It also depends on which switch/switches you are using as to what type of

teaming you will get. The Nics need to be plugged into the same physical

switch unless you have a stack of switches which act as one physical unit.

 

If you plug each nic into a different switch you'll end up with problems.

Then dependent on your actual switch you will get either 1 nic receiving all

data packets and both sending data or both nics sending and receiving. This

is all dependent upon your switches.

 

They can also be configured as basic failover but you may as well utilise

the extra bandwidth and have the failover aswell.

 

Regards

 

Chris

 

If yout team the NIC's they need to be either plugged into the same switch

 

"Rich" <Rich@discussions.microsoft.com> wrote in message

news:59C24402-6A08-435C-805A-E505201833EE@microsoft.com...

> Depending on the manufacturer what it's called will be different, but you

> can

> set up a virtual NIC, which is really just the two NICs teamed together

> for

> load balancing or fault tolerance, whichever you prefer. then you just

> put

> the IP on the virtual NIC.

> the info will either load balance between the 2 NICs or just go to the one

> (if going with fault tolerance).

>

>

> "pvong" wrote:

>

>> I'm a newbie so please explain.

>>

>> I got a couple of servers running running w2003 with dual NICs. I'm

>> trying

>> to figure out how to use the dual NICs.

>> 1) Do you guys assign different IPs to each NIC? If so, do you make two

>> different A records for the same server except with two different IPs?

>> 2) Even though each NIC has it's own MAC address, can I assign them with

>> the

>> same IP number?

>>

>> Basically, I'm trying to see if can use both NICs at the same time. I

>> don't

>> understand if some request information to an IP and I have 2 NICs with

>> the

>> same IP, will the request happen twice? This would create overhead.

>>

>> Please educate me like I'm a newbie who just started working with this

>> stuff.

>>

>> Thanks!

>> Phil

>>

>>

>>

[Guest pvong]

Re: Dual NIC education

 

Thanks guys! Have any idea where I can find some simple learning

instructions about this on the net?

Thanks!

 

 

"Chris D" <cdove@no.myrealbox.spam.com> wrote in message

news:ewiX1eaxIHA.2188@TK2MSFTNGP04.phx.gbl...

> It also depends on which switch/switches you are using as to what type of

> teaming you will get. The Nics need to be plugged into the same physical

> switch unless you have a stack of switches which act as one physical unit.

>

> If you plug each nic into a different switch you'll end up with problems.

> Then dependent on your actual switch you will get either 1 nic receiving

> all data packets and both sending data or both nics sending and receiving.

> This is all dependent upon your switches.

>

> They can also be configured as basic failover but you may as well utilise

> the extra bandwidth and have the failover aswell.

>

> Regards

>

> Chris

>

> If yout team the NIC's they need to be either plugged into the same switch

>

> "Rich" <Rich@discussions.microsoft.com> wrote in message

> news:59C24402-6A08-435C-805A-E505201833EE@microsoft.com...

>> Depending on the manufacturer what it's called will be different, but you

>> can

>> set up a virtual NIC, which is really just the two NICs teamed together

>> for

>> load balancing or fault tolerance, whichever you prefer. then you just

>> put

>> the IP on the virtual NIC.

>> the info will either load balance between the 2 NICs or just go to the

>> one

>> (if going with fault tolerance).

>>

>>

>> "pvong" wrote:

>>

>>> I'm a newbie so please explain.

>>>

>>> I got a couple of servers running running w2003 with dual NICs. I'm

>>> trying

>>> to figure out how to use the dual NICs.

>>> 1) Do you guys assign different IPs to each NIC? If so, do you make two

>>> different A records for the same server except with two different IPs?

>>> 2) Even though each NIC has it's own MAC address, can I assign them with

>>> the

>>> same IP number?

>>>

>>> Basically, I'm trying to see if can use both NICs at the same time. I

>>> don't

>>> understand if some request information to an IP and I have 2 NICs with

>>> the

>>> same IP, will the request happen twice? This would create overhead.

>>>

>>> Please educate me like I'm a newbie who just started working with this

>>> stuff.

>>>

>>> Thanks!

>>> Phil

>>>

>>>

>>>

>

>

[Guest Chris D]

Re: Dual NIC education

 

Best thing to do is have a read of the help file sin the vendors teaming

software. I've found these very good.

 

"pvong" <phillip*at*yahoo*dot*com> wrote in message

news:eCkWv$axIHA.420@TK2MSFTNGP02.phx.gbl...

> Thanks guys! Have any idea where I can find some simple learning

> instructions about this on the net?

> Thanks!

>

>

> "Chris D" <cdove@no.myrealbox.spam.com> wrote in message

> news:ewiX1eaxIHA.2188@TK2MSFTNGP04.phx.gbl...

>> It also depends on which switch/switches you are using as to what type of

>> teaming you will get. The Nics need to be plugged into the same physical

>> switch unless you have a stack of switches which act as one physical

>> unit.

>>

>> If you plug each nic into a different switch you'll end up with problems.

>> Then dependent on your actual switch you will get either 1 nic receiving

>> all data packets and both sending data or both nics sending and

>> receiving. This is all dependent upon your switches.

>>

>> They can also be configured as basic failover but you may as well utilise

>> the extra bandwidth and have the failover aswell.

>>

>> Regards

>>

>> Chris

>>

>> If yout team the NIC's they need to be either plugged into the same

>> switch

>>

>> "Rich" <Rich@discussions.microsoft.com> wrote in message

>> news:59C24402-6A08-435C-805A-E505201833EE@microsoft.com...

>>> Depending on the manufacturer what it's called will be different, but

>>> you can

>>> set up a virtual NIC, which is really just the two NICs teamed together

>>> for

>>> load balancing or fault tolerance, whichever you prefer. then you just

>>> put

>>> the IP on the virtual NIC.

>>> the info will either load balance between the 2 NICs or just go to the

>>> one

>>> (if going with fault tolerance).

>>>

>>>

>>> "pvong" wrote:

>>>

>>>> I'm a newbie so please explain.

>>>>

>>>> I got a couple of servers running running w2003 with dual NICs. I'm

>>>> trying

>>>> to figure out how to use the dual NICs.

>>>> 1) Do you guys assign different IPs to each NIC? If so, do you make

>>>> two

>>>> different A records for the same server except with two different IPs?

>>>> 2) Even though each NIC has it's own MAC address, can I assign them

>>>> with the

>>>> same IP number?

>>>>

>>>> Basically, I'm trying to see if can use both NICs at the same time. I

>>>> don't

>>>> understand if some request information to an IP and I have 2 NICs with

>>>> the

>>>> same IP, will the request happen twice? This would create overhead.

>>>>

>>>> Please educate me like I'm a newbie who just started working with this

>>>> stuff.

>>>>

>>>> Thanks!

>>>> Phil

>>>>

>>>>

>>>>

>>

>>

>

>