[OT?] CD-ROM and Hard Drive on Same Cable

[Guest W. Watson]

I can't find a suitable PC hardware NG that looks current, so I'll post here

until someone directs me to a better NG.

 

It's been awhile since I played hook up with drives. Here's my problem. I

have a CD-ROM drive at the end of a cable. It works fine. I thought I'd

stick a HD in as a slave. It doesn't get detected. I made it a slave.

However, I have no idea what the CD-ROM thinks it is--Ah, master according

to BIOS. It looks like it has two jumpers. (What are the jumper

possibilities for it?) It's a 56x Disc shown in BIOS as G6D M1.30. I'm

pretty sure the cables are 48-pin. The HD is a boot disk from an older

system, and is in a removable drive (handle on front). It seems seated and

I'm pretty confident it's powered up, although the removable container has

no LED. (I switched power with the CD-ROM to test it.) Is it not possible to

put a HD on the same cable with a CD-ROM?

 

The CD-ROM is on the end of it's cable. The connector at the end of the

cable has one (center) pin missing, so I can't put the HD in it.

 

I could put the HD on the same cable with my W2K boot-up HD, but the cable

positioning is a little weird. I'd need to re-arrange the position of the

removable drive a bit.

--

Wayne Watson (Nevada City, CA)

 

Web Page: <speckledwithStars.net>

[Guest Dave Patrick]

Re: [OT?] CD-ROM and Hard Drive on Same Cable

 

It will work (assuming the jumpers are correct) but the controller can only

access one device (on a given channel) at a time so putting the cd-rom on

the same channel as a fixed disk is probably going to slow access to your

disk.

 

--

 

Regards,

 

Dave Patrick ....Please no email replies - reply in newsgroup.

Microsoft Certified Professional

Microsoft MVP [Windows]

http://www.microsoft.com/protect

 

"W. Watson" wrote:

>I can't find a suitable PC hardware NG that looks current, so I'll post

>here until someone directs me to a better NG.

>

> It's been awhile since I played hook up with drives. Here's my problem. I

> have a CD-ROM drive at the end of a cable. It works fine. I thought I'd

> stick a HD in as a slave. It doesn't get detected. I made it a slave.

> However, I have no idea what the CD-ROM thinks it is--Ah, master according

> to BIOS. It looks like it has two jumpers. (What are the jumper

> possibilities for it?) It's a 56x Disc shown in BIOS as G6D M1.30. I'm

> pretty sure the cables are 48-pin. The HD is a boot disk from an older

> system, and is in a removable drive (handle on front). It seems seated and

> I'm pretty confident it's powered up, although the removable container has

> no LED. (I switched power with the CD-ROM to test it.) Is it not possible

> to put a HD on the same cable with a CD-ROM?

>

> The CD-ROM is on the end of it's cable. The connector at the end of the

> cable has one (center) pin missing, so I can't put the HD in it.

>

> I could put the HD on the same cable with my W2K boot-up HD, but the cable

> positioning is a little weird. I'd need to re-arrange the position of the

> removable drive a bit.

> --

> Wayne Watson (Nevada City, CA)

>

> Web Page: <speckledwithStars.net>

[Guest Frank Booth Snr]

Re: [OT?] CD-ROM and Hard Drive on Same Cable

 

W. Watson wrote:

> I can't find a suitable PC hardware NG that looks current, so I'll post

> here until someone directs me to a better NG.

>

> It's been awhile since I played hook up with drives. Here's my problem.

> I have a CD-ROM drive at the end of a cable. It works fine. I thought

> I'd stick a HD in as a slave. It doesn't get detected. I made it a

> slave. However, I have no idea what the CD-ROM thinks it is--Ah, master

> according to BIOS. It looks like it has two jumpers. (What are the

> jumper possibilities for it?) It's a 56x Disc shown in BIOS as G6D

> M1.30. I'm pretty sure the cables are 48-pin. The HD is a boot disk from

> an older system, and is in a removable drive (handle on front). It seems

> seated and I'm pretty confident it's powered up, although the removable

> container has no LED. (I switched power with the CD-ROM to test it.) Is

> it not possible to put a HD on the same cable with a CD-ROM?

>

> The CD-ROM is on the end of it's cable. The connector at the end of the

> cable has one (center) pin missing, so I can't put the HD in it.

>

> I could put the HD on the same cable with my W2K boot-up HD, but the

> cable positioning is a little weird. I'd need to re-arrange the position

> of the removable drive a bit.

 

It's better (though not essential) to have a boot up disk as an internal

hdd, with backup disks as external or internal drives. I presume from

what your saying that your disk controllers are IDE. The boot hdd should

certainly be able to be fitted into an IDE cable connector. The ribbon

cable connector has holes, not pins, and one central hole missing is

normal for an 80 pin cable connector. It will only fit one way.

 

The CDROM drive can be fitted on the same cable as the hdd, but that

should be a slave (middle connector) with the hdd drive fitted to the

end connector as a master. The other cable end must be attached to IDE

controller 0 (primary controller). It is better practice to fit the

CDROM drive on the other (secondary) cable ribbon as a master if no

other drive is attached.

 

Jumpering the hdd/CDROM depends on its make as this varies according to

manufacturer. If you look just above the jumper pins on the drives, it

often (but not always) shows which pins are designated for master, slave

etc in tiny initials.

[Guest W. Watson]

Re: [OT?] CD-ROM and Hard Drive on Same Cable

 

 

 

Frank Booth Snr wrote:

> W. Watson wrote:

>

>> I can't find a suitable PC hardware NG that looks current, so I'll

>> post here until someone directs me to a better NG.

>>

>> It's been awhile since I played hook up with drives. Here's my

>> problem. I have a CD-ROM drive at the end of a cable. It works fine. I

>> thought I'd stick a HD in as a slave. It doesn't get detected. I made

>> it a slave. However, I have no idea what the CD-ROM thinks it is--Ah,

>> master according to BIOS. It looks like it has two jumpers. (What are

>> the jumper possibilities for it?) It's a 56x Disc shown in BIOS as G6D

>> M1.30. I'm pretty sure the cables are 48-pin. The HD is a boot disk

>> from an older system, and is in a removable drive (handle on front).

>> It seems seated and I'm pretty confident it's powered up, although the

>> removable container has no LED. (I switched power with the CD-ROM to

>> test it.) Is it not possible to put a HD on the same cable with a CD-ROM?

>>

>> The CD-ROM is on the end of it's cable. The connector at the end of

>> the cable has one (center) pin missing, so I can't put the HD in it.

>>

>> I could put the HD on the same cable with my W2K boot-up HD, but the

>> cable positioning is a little weird. I'd need to re-arrange the

>> position of the removable drive a bit.

>

> It's better (though not essential) to have a boot up disk as an internal

> hdd, with backup disks as external or internal drives. I presume from

> what your saying that your disk controllers are IDE. The boot hdd should

> certainly be able to be fitted into an IDE cable connector. The ribbon

> cable connector has holes, not pins, and one central hole missing is

> normal for an 80 pin cable connector. It will only fit one way.

>

> The CDROM drive can be fitted on the same cable as the hdd, but that

> should be a slave (middle connector) with the hdd drive fitted to the

> end connector as a master. The other cable end must be attached to IDE

> controller 0 (primary controller). It is better practice to fit the

> CDROM drive on the other (secondary) cable ribbon as a master if no

> other drive is attached.

>

> Jumpering the hdd/CDROM depends on its make as this varies according to

> manufacturer. If you look just above the jumper pins on the drives, it

> often (but not always) shows which pins are designated for master, slave

> etc in tiny initials.

 

Yes, IDE. Effectively it is an internal HDD. It is cabled in to the middle

connector of the 48-pin cable on the secondary controller. The removable

drawer/try is pressed in all the way and seems to have the feel of being

plugged in at the back. I'm booting up off of the primary controller into

W2K. That works fine. However, I cannot see a HDD on the secondary

controller. Since BIOS is telling me the CD-ROM is master, I'll go with that.

 

It's too bad that there no LED on the Western Digital (WD) HD. BTW, it

contains data I want to extract. True it's a boot disk, but that's not its

function here. I just want to mount it and get the data on it.

 

My last resort is to move the WD into a slave position on the primary

controller. It's awkward mechanically, but that way I can be sure it's

really getting power.

 

--

Wayne Watson (Nevada City, CA)

 

Web Page: <speckledwithStars.net>

[Guest W. Watson]

Re: [OT?] CD-ROM and Hard Drive on Same Cable

 

Solved. After moving cables, etc. around, I forgot to put the jumper in the

correct spot. All is well.

 

W. Watson wrote:

>

>

> Frank Booth Snr wrote:

>> W. Watson wrote:

>>

>>> I can't find a suitable PC hardware NG that looks current, so I'll

>>> post here until someone directs me to a better NG.

>>>

>>> It's been awhile since I played hook up with drives. Here's my

>>> problem. I have a CD-ROM drive at the end of a cable. It works fine.

>>> I thought I'd stick a HD in as a slave. It doesn't get detected. I

>>> made it a slave. However, I have no idea what the CD-ROM thinks it

>>> is--Ah, master according to BIOS. It looks like it has two jumpers.

>>> (What are the jumper possibilities for it?) It's a 56x Disc shown in

>>> BIOS as G6D M1.30. I'm pretty sure the cables are 48-pin. The HD is a

>>> boot disk from an older system, and is in a removable drive (handle

>>> on front). It seems seated and I'm pretty confident it's powered up,

>>> although the removable container has no LED. (I switched power with

>>> the CD-ROM to test it.) Is it not possible to put a HD on the same

>>> cable with a CD-ROM?

>>>

>>> The CD-ROM is on the end of it's cable. The connector at the end of

>>> the cable has one (center) pin missing, so I can't put the HD in it.

>>>

>>> I could put the HD on the same cable with my W2K boot-up HD, but the

>>> cable positioning is a little weird. I'd need to re-arrange the

>>> position of the removable drive a bit.

>>

>> It's better (though not essential) to have a boot up disk as an

>> internal hdd, with backup disks as external or internal drives. I

>> presume from what your saying that your disk controllers are IDE. The

>> boot hdd should certainly be able to be fitted into an IDE cable

>> connector. The ribbon cable connector has holes, not pins, and one

>> central hole missing is normal for an 80 pin cable connector. It will

>> only fit one way.

>>

>> The CDROM drive can be fitted on the same cable as the hdd, but that

>> should be a slave (middle connector) with the hdd drive fitted to the

>> end connector as a master. The other cable end must be attached to IDE

>> controller 0 (primary controller). It is better practice to fit the

>> CDROM drive on the other (secondary) cable ribbon as a master if no

>> other drive is attached.

>>

>> Jumpering the hdd/CDROM depends on its make as this varies according

>> to manufacturer. If you look just above the jumper pins on the drives,

>> it often (but not always) shows which pins are designated for master,

>> slave etc in tiny initials.

>

> Yes, IDE. Effectively it is an internal HDD. It is cabled in to the

> middle connector of the 48-pin cable on the secondary controller. The

> removable drawer/try is pressed in all the way and seems to have the

> feel of being plugged in at the back. I'm booting up off of the primary

> controller into W2K. That works fine. However, I cannot see a HDD on the

> secondary controller. Since BIOS is telling me the CD-ROM is master,

> I'll go with that.

>

> It's too bad that there no LED on the Western Digital (WD) HD. BTW, it

> contains data I want to extract. True it's a boot disk, but that's not

> its function here. I just want to mount it and get the data on it.

>

> My last resort is to move the WD into a slave position on the primary

> controller. It's awkward mechanically, but that way I can be sure it's

> really getting power.

>

 

--

Wayne Watson (Nevada City, CA)

 

Web Page: <speckledwithStars.net>