general question

[Guest rb]

OK. Found a WSM 2000 buried deep in my closet. Tried to get it going.

So far, it comes on and warms up fairly nicely. Then, the blue screen of

death comes up and tell me theres some kernel fault, and all my data is

being dumped to "somewhere". Thats all she wrote on that part.

 

1. Is this meaning something else is going on in relation to the disk?

 

2. I've run a copy of Windows 2000 on it, and it seems not to like that

(does the same thing).

 

3. What do I do to get it going again?

[Guest Dave Patrick]

Re: general question

 

Not sure about "WSM" but I'd try a clean installation.

 

To do a clean install, either boot the Windows 2000 install CD-Rom or setup

disks. The set of four install disks can be created from your Windows 2000

CD-Rom; change to the \bootdisk directory on the CD-Rom and execute

makeboot.exe (from dos) or makebt32.exe (from 32 bit) and follow the

prompts.

 

(Note: If your drive controller is not natively supported then you'll want

to boot the Windows 2000 install CD-Rom. Then *F6* very early and very

important (at setup is inspecting your system) in the setup to prevent drive

controller detection, and select S to specify additional drivers. Then later

you'll be prompted to insert the manufacturer supplied Windows 2000 driver

for your drive controller in drive "A")

 

Setup inspects your computer's hardware configuration and then begins to

install the Setup and driver files. When the Windows 2000 Professional

screen appears, press ENTER to set up Windows 2000 Professional.

 

Read the license agreement, and then press the F8 key to accept the terms of

the license agreement and continue the installation.

 

When the Windows 2000 Professional Setup screen appears, all the existing

partitions and the unpartitioned spaces are listed for each physical hard

disk. Use the ARROW keys to select the partitions Press D to delete an

existing partition, If you press D to delete an existing partition, you must

then press L (or press ENTER, and then press L if it is the System

partition) to confirm that you want to delete the partition. Repeat this

step for each of the existing partitions When all the partitions are deleted

press F3 to exit setup, (to avoid unexpected drive letter assignments with

your new install) then restart the pc then when you get to this point in

setup again select the unpartitioned space, and then press C to create a new

partition and specify the size (if required). Windows will by default use

all available space.

 

Be sure to apply SP4 and these two below to your new install before

connecting to any network. Internet included. (sasser, msblast)

http://download.microsoft.com/download/E/6/A/E6A04295-D2A8-40D0-A0C5-241BFECD095E/W2KSP4_EN.EXE

http://www.microsoft.com/technet/security/bulletin/MS03-043.mspx

http://www.microsoft.com/technet/security/bulletin/MS03-049.mspx

 

Then

 

Rollup 1 for Microsoft Windows 2000 Service Pack 4

http://www.microsoft.com/downloads/details.aspx?amp;displaylang=en&familyid=B54730CF-8850-4531-B52B-BF28B324C662&displaylang=en

 

 

 

--

 

Regards,

 

Dave Patrick ....Please no email replies - reply in newsgroup.

Microsoft Certified Professional

Microsoft MVP [Windows]

http://www.microsoft.com/protect

 

"rb" wrote:

> OK. Found a WSM 2000 buried deep in my closet. Tried to get it going.

> So far, it comes on and warms up fairly nicely. Then, the blue screen of

> death comes up and tell me theres some kernel fault, and all my data is

> being dumped to "somewhere". Thats all she wrote on that part.

>

> 1. Is this meaning something else is going on in relation to the disk?

>

> 2. I've run a copy of Windows 2000 on it, and it seems not to like that

> (does the same thing).

>

> 3. What do I do to get it going again?

>

[Guest rb]

Re: general question

 

I have no idea where I came up with "WSM". I meant Windows 2000.

 

Yes to clean install.