Getting rid of an old bootable partition...

October 6, 2007

Hi all,

I used to have XP 32-bit on my C: drive. Shortly after XP 64-bit came out,

I installed in on D: and started dual-booting. It didn't take long after

I've completed my migration that I started using x64 exclusively. My

system's gone through a few hardware changes since then, but I've never

bothered to reboot in XP 32-bit to install drivers and such. A while ago I

did try to boot into XP 32-bit (can't remember why I would do such a foolish

thing) ;-) but I found out at that time that my 32-bit installation was

corrupted.

I can't say I cared enough about it to try to fix it or even figure out why

it wasn't functional anymore. In fact I'd prefer to have it gone

completely.

Both partitions (C: and D:) are 30GB in size, on the same physical hard

drive (250GB SATA). The C: partition (obviously in such a setup) contains

the boot.ini file. Given that I have no need for XP 32-bit, and my D:

partition could use the space, I thought I could get rid of the C: partition

entirely.

So I'm asking for advice on exactly how I could proceed, given that XP's

disk manager doesn't really have the smarts to do such a thing.

At a minimum I would expect I would have to copy the boot.ini, ntdetect.com

and ntldr files from C: to D: before I blow away the C: partition (and

resize D: to take up that free space)...maybe edit the boot.ini so any

reference to ...rdisk(0)partition(2) becomes rdisk(0)partition(1)...but then

I'm pretty sure I'll run into further problems because C: drive is currently

a primary partition, while D: (and E:, F:, G:, and a couple more) are all

logical partitions grouped within one extended partition.

I'm not looking to change XP x64's drive letter assignment from D: back to

C:...in fact if it does that, that'll screw up *all* references pretty good.

I just want the C: partition to go away.

I know that at least one of these steps isn't supported by Disk Manager

itself (resizing my D: partition), so I'm looking for a good tool (Partition

Magic, or something from Acronis?) that is *known* to be able to do these

sort of changes intelligently and won't leave me with a system that won't

boot...

Anybody gone through this process?

October 6, 2007

Re: Getting rid of an old bootable partition...

If you're not trying to change the drive letters, make your life easier -

use one of the smart partition products (I like Acronis), to resize your C:

down to tiny, and fill up the extra space by growing the D: partition. I'd

leave C: just big enough to not have it get excited if some ill-behaved

program decided to dump it's files there, and so that you can have the dump

file there. Say 5GB?

By doing it this way, you don't have to move any files, just delete all the

old ones that you don't want that are on there. And, of course, edit your

boot.ini file to get rid of any reference to that partition. ;)

--

Charlie.

http://msmvps.com/xperts64

http://mvp.support.microsoft.com/profile/charlie.russel

"Homer J. Simpson" <root@127.0.0.1> wrote in message

news:%232RNyjDCIHA.4476@TK2MSFTNGP06.phx.gbl...

> Hi all,

>

> I used to have XP 32-bit on my C: drive. Shortly after XP 64-bit came

> out, I installed in on D: and started dual-booting. It didn't take long

> after I've completed my migration that I started using x64 exclusively.

> My system's gone through a few hardware changes since then, but I've never

> bothered to reboot in XP 32-bit to install drivers and such. A while ago

> I did try to boot into XP 32-bit (can't remember why I would do such a

> foolish thing) ;-) but I found out at that time that my 32-bit

> installation was corrupted.

>

> I can't say I cared enough about it to try to fix it or even figure out

> why it wasn't functional anymore. In fact I'd prefer to have it gone

> completely.

>

> Both partitions (C: and D:) are 30GB in size, on the same physical hard

> drive (250GB SATA). The C: partition (obviously in such a setup) contains

> the boot.ini file. Given that I have no need for XP 32-bit, and my D:

> partition could use the space, I thought I could get rid of the C:

> partition entirely.

>

> So I'm asking for advice on exactly how I could proceed, given that XP's

> disk manager doesn't really have the smarts to do such a thing.

>

> At a minimum I would expect I would have to copy the boot.ini,

> ntdetect.com and ntldr files from C: to D: before I blow away the C:

> partition (and resize D: to take up that free space)...maybe edit the

> boot.ini so any reference to ...rdisk(0)partition(2) becomes

> rdisk(0)partition(1)...but then I'm pretty sure I'll run into further

> problems because C: drive is currently a primary partition, while D: (and

> E:, F:, G:, and a couple more) are all logical partitions grouped within

> one extended partition.

>

> I'm not looking to change XP x64's drive letter assignment from D: back to

> C:...in fact if it does that, that'll screw up *all* references pretty

> good. I just want the C: partition to go away.

>

> I know that at least one of these steps isn't supported by Disk Manager

> itself (resizing my D: partition), so I'm looking for a good tool

> (Partition Magic, or something from Acronis?) that is *known* to be able

> to do these sort of changes intelligently and won't leave me with a system

> that won't boot...

>

> Anybody gone through this process?

>

October 6, 2007

Re: Getting rid of an old bootable partition...

Hi Homer,

You are running Windows XP Professional x64 Edition Service Pack 2. Are

you able to download directly into your Briefcase Folder within this

operating system?

Now if you want to get rid of Drive C:, you can and have it part of

Drive D:. However, you will need to reinstall Windows XP Professional x64

Edition Service Pack 2. Why? Because all the programs you have installed in

X64 Edition were installed pointing to their location on Drive D: and not on

Drive C:

You can use Acronis Disk Director Suite to decease the size of C: or you

can just delete the files and sub-folders of Drive C: and use Drive C: as a

storage Drive. Move your Documents folder to Drive C:, freeing up more space

on Drive D: for additional program files.

--

thecreator

"Homer J. Simpson" <root@127.0.0.1> wrote in message

news:%232RNyjDCIHA.4476@TK2MSFTNGP06.phx.gbl...

> Hi all,

>

> I used to have XP 32-bit on my C: drive. Shortly after XP 64-bit came

> out, I installed in on D: and started dual-booting. It didn't take long

> after I've completed my migration that I started using x64 exclusively.

> My system's gone through a few hardware changes since then, but I've never

> bothered to reboot in XP 32-bit to install drivers and such. A while ago

> I did try to boot into XP 32-bit (can't remember why I would do such a

> foolish thing) ;-) but I found out at that time that my 32-bit

> installation was corrupted.

>

> I can't say I cared enough about it to try to fix it or even figure out

> why it wasn't functional anymore. In fact I'd prefer to have it gone

> completely.

>

> Both partitions (C: and D:) are 30GB in size, on the same physical hard

> drive (250GB SATA). The C: partition (obviously in such a setup) contains

> the boot.ini file. Given that I have no need for XP 32-bit, and my D:

> partition could use the space, I thought I could get rid of the C:

> partition entirely.

>

> So I'm asking for advice on exactly how I could proceed, given that XP's

> disk manager doesn't really have the smarts to do such a thing.

>

> At a minimum I would expect I would have to copy the boot.ini,

> ntdetect.com and ntldr files from C: to D: before I blow away the C:

> partition (and resize D: to take up that free space)...maybe edit the

> boot.ini so any reference to ...rdisk(0)partition(2) becomes

> rdisk(0)partition(1)...but then I'm pretty sure I'll run into further

> problems because C: drive is currently a primary partition, while D: (and

> E:, F:, G:, and a couple more) are all logical partitions grouped within

> one extended partition.

>

> I'm not looking to change XP x64's drive letter assignment from D: back to

> C:...in fact if it does that, that'll screw up *all* references pretty

> good. I just want the C: partition to go away.

>

> I know that at least one of these steps isn't supported by Disk Manager

> itself (resizing my D: partition), so I'm looking for a good tool

> (Partition Magic, or something from Acronis?) that is *known* to be able

> to do these sort of changes intelligently and won't leave me with a system

> that won't boot...

>

> Anybody gone through this process?

>

October 7, 2007

Re: Getting rid of an old bootable partition...

And that would be Acronis Disk Director Suite 10.0

http://www.acronis.com/enterprise/products/diskdirectorsuite/

:)

Carlos

"Charlie Russel - MVP" wrote:

> If you're not trying to change the drive letters, make your life easier -

> use one of the smart partition products (I like Acronis), to resize your C:

> down to tiny, and fill up the extra space by growing the D: partition. I'd

> leave C: just big enough to not have it get excited if some ill-behaved

> program decided to dump it's files there, and so that you can have the dump

> file there. Say 5GB?

>

> By doing it this way, you don't have to move any files, just delete all the

> old ones that you don't want that are on there. And, of course, edit your

> boot.ini file to get rid of any reference to that partition. ;)

>

> --

> Charlie.

> http://msmvps.com/xperts64

> http://mvp.support.microsoft.com/profile/charlie.russel

>

> "Homer J. Simpson" <root@127.0.0.1> wrote in message

> news:%232RNyjDCIHA.4476@TK2MSFTNGP06.phx.gbl...

> > Hi all,

> >

> > I used to have XP 32-bit on my C: drive. Shortly after XP 64-bit came

> > out, I installed in on D: and started dual-booting. It didn't take long

> > after I've completed my migration that I started using x64 exclusively.

> > My system's gone through a few hardware changes since then, but I've never

> > bothered to reboot in XP 32-bit to install drivers and such. A while ago

> > I did try to boot into XP 32-bit (can't remember why I would do such a

> > foolish thing) ;-) but I found out at that time that my 32-bit

> > installation was corrupted.

> >

> > I can't say I cared enough about it to try to fix it or even figure out

> > why it wasn't functional anymore. In fact I'd prefer to have it gone

> > completely.

> >

> > Both partitions (C: and D:) are 30GB in size, on the same physical hard

> > drive (250GB SATA). The C: partition (obviously in such a setup) contains

> > the boot.ini file. Given that I have no need for XP 32-bit, and my D:

> > partition could use the space, I thought I could get rid of the C:

> > partition entirely.

> >

> > So I'm asking for advice on exactly how I could proceed, given that XP's

> > disk manager doesn't really have the smarts to do such a thing.

> >

> > At a minimum I would expect I would have to copy the boot.ini,

> > ntdetect.com and ntldr files from C: to D: before I blow away the C:

> > partition (and resize D: to take up that free space)...maybe edit the

> > boot.ini so any reference to ...rdisk(0)partition(2) becomes

> > rdisk(0)partition(1)...but then I'm pretty sure I'll run into further

> > problems because C: drive is currently a primary partition, while D: (and

> > E:, F:, G:, and a couple more) are all logical partitions grouped within

> > one extended partition.

> >

> > I'm not looking to change XP x64's drive letter assignment from D: back to

> > C:...in fact if it does that, that'll screw up *all* references pretty

> > good. I just want the C: partition to go away.

> >

> > I know that at least one of these steps isn't supported by Disk Manager

> > itself (resizing my D: partition), so I'm looking for a good tool

> > (Partition Magic, or something from Acronis?) that is *known* to be able

> > to do these sort of changes intelligently and won't leave me with a system

> > that won't boot...

> >

> > Anybody gone through this process?

> >

>

October 7, 2007

Re: Getting rid of an old bootable partition...

I agree with Charlie except I would probably make the C partition smaller.

You have to have the system files on a primary partition in Windows, so you

can't have your system files on D. Files like nVidia drivers are dumb and

have to be on the C drive also. Nothing else I have does, but you ever

know.

My favourite for file and partition manipulation is BootItNG, but Acronis is

supposed to work fine.

"Homer J. Simpson" <root@127.0.0.1> wrote in message

news:%232RNyjDCIHA.4476@TK2MSFTNGP06.phx.gbl...

> Hi all,

>

> I used to have XP 32-bit on my C: drive. Shortly after XP 64-bit came

> out, I installed in on D: and started dual-booting. It didn't take long

> after I've completed my migration that I started using x64 exclusively.

> My system's gone through a few hardware changes since then, but I've never

> bothered to reboot in XP 32-bit to install drivers and such. A while ago

> I did try to boot into XP 32-bit (can't remember why I would do such a

> foolish thing) ;-) but I found out at that time that my 32-bit

> installation was corrupted.

>

> I can't say I cared enough about it to try to fix it or even figure out

> why it wasn't functional anymore. In fact I'd prefer to have it gone

> completely.

>

> Both partitions (C: and D:) are 30GB in size, on the same physical hard

> drive (250GB SATA). The C: partition (obviously in such a setup) contains

> the boot.ini file. Given that I have no need for XP 32-bit, and my D:

> partition could use the space, I thought I could get rid of the C:

> partition entirely.

>

> So I'm asking for advice on exactly how I could proceed, given that XP's

> disk manager doesn't really have the smarts to do such a thing.

>

> At a minimum I would expect I would have to copy the boot.ini,

> ntdetect.com and ntldr files from C: to D: before I blow away the C:

> partition (and resize D: to take up that free space)...maybe edit the

> boot.ini so any reference to ...rdisk(0)partition(2) becomes

> rdisk(0)partition(1)...but then I'm pretty sure I'll run into further

> problems because C: drive is currently a primary partition, while D: (and

> E:, F:, G:, and a couple more) are all logical partitions grouped within

> one extended partition.

>

> I'm not looking to change XP x64's drive letter assignment from D: back to

> C:...in fact if it does that, that'll screw up *all* references pretty

> good. I just want the C: partition to go away.

>

> I know that at least one of these steps isn't supported by Disk Manager

> itself (resizing my D: partition), so I'm looking for a good tool

> (Partition Magic, or something from Acronis?) that is *known* to be able

> to do these sort of changes intelligently and won't leave me with a system

> that won't boot...

>

> Anybody gone through this process?

>

October 7, 2007

Re: Getting rid of an old bootable partition...

Yup. That it would. :)

--

Charlie.

http://msmvps.com/xperts64

http://mvp.support.microsoft.com/profile/charlie.russel

"Carlos" <Carlos@discussions.microsoft.com> wrote in message

news:6B7961E2-0C2B-4FE0-98C6-5D3CC8EE4694@microsoft.com...

> And that would be Acronis Disk Director Suite 10.0

> http://www.acronis.com/enterprise/products/diskdirectorsuite/

> :)

> Carlos

>

> "Charlie Russel - MVP" wrote:

>

>> If you're not trying to change the drive letters, make your life easier -

>> use one of the smart partition products (I like Acronis), to resize your

>> C:

>> down to tiny, and fill up the extra space by growing the D: partition.

>> I'd

>> leave C: just big enough to not have it get excited if some ill-behaved

>> program decided to dump it's files there, and so that you can have the

>> dump

>> file there. Say 5GB?

>>

>> By doing it this way, you don't have to move any files, just delete all

>> the

>> old ones that you don't want that are on there. And, of course, edit your

>> boot.ini file to get rid of any reference to that partition. ;)

>>

>> --

>> Charlie.

>> http://msmvps.com/xperts64

>> http://mvp.support.microsoft.com/profile/charlie.russel

>>

>> "Homer J. Simpson" <root@127.0.0.1> wrote in message

>> news:%232RNyjDCIHA.4476@TK2MSFTNGP06.phx.gbl...

>> > Hi all,

>> >

>> > I used to have XP 32-bit on my C: drive. Shortly after XP 64-bit came

>> > out, I installed in on D: and started dual-booting. It didn't take

>> > long

>> > after I've completed my migration that I started using x64 exclusively.

>> > My system's gone through a few hardware changes since then, but I've

>> > never

>> > bothered to reboot in XP 32-bit to install drivers and such. A while

>> > ago

>> > I did try to boot into XP 32-bit (can't remember why I would do such a

>> > foolish thing) ;-) but I found out at that time that my 32-bit

>> > installation was corrupted.

>> >

>> > I can't say I cared enough about it to try to fix it or even figure out

>> > why it wasn't functional anymore. In fact I'd prefer to have it gone

>> > completely.

>> >

>> > Both partitions (C: and D:) are 30GB in size, on the same physical hard

>> > drive (250GB SATA). The C: partition (obviously in such a setup)

>> > contains

>> > the boot.ini file. Given that I have no need for XP 32-bit, and my D:

>> > partition could use the space, I thought I could get rid of the C:

>> > partition entirely.

>> >

>> > So I'm asking for advice on exactly how I could proceed, given that

>> > XP's

>> > disk manager doesn't really have the smarts to do such a thing.

>> >

>> > At a minimum I would expect I would have to copy the boot.ini,

>> > ntdetect.com and ntldr files from C: to D: before I blow away the C:

>> > partition (and resize D: to take up that free space)...maybe edit the

>> > boot.ini so any reference to ...rdisk(0)partition(2) becomes

>> > rdisk(0)partition(1)...but then I'm pretty sure I'll run into further

>> > problems because C: drive is currently a primary partition, while D:

>> > (and

>> > E:, F:, G:, and a couple more) are all logical partitions grouped

>> > within

>> > one extended partition.

>> >

>> > I'm not looking to change XP x64's drive letter assignment from D: back

>> > to

>> > C:...in fact if it does that, that'll screw up *all* references pretty

>> > good. I just want the C: partition to go away.

>> >

>> > I know that at least one of these steps isn't supported by Disk Manager

>> > itself (resizing my D: partition), so I'm looking for a good tool

>> > (Partition Magic, or something from Acronis?) that is *known* to be

>> > able

>> > to do these sort of changes intelligently and won't leave me with a

>> > system

>> > that won't boot...

>> >

>> > Anybody gone through this process?

>> >

>>

October 7, 2007

Re: Getting rid of an old bootable partition...

Thanks to all who replied. I knew the most straightforward thing to do was

to reduce the size of the C: partition down to nothing (and reallocate its

space to D:), and leave the boot files there, but my preference would've

been to remove it completely. I thought something like Acronis would've

been able to change my D: partition from Extended to Primary, but if it

can't do that, then it looks like I'm really SOL.

October 7, 2007

Re: Getting rid of an old bootable partition...

Acronis will do that, I think. BUT, you'll still end up with problems. Now

the computer will think that your system drive is C: not D: (and you can't

change the assigned drive letter of a system partition.) That would break

way more than just Windows, which could probably sort of cope. And when you

were all done? You'd have an odd machine that didn't behave normally. To my

mind, that leaves two possibilities - leave the legacy C: there, or

re-partition and rebuild.

--

Charlie.

http://msmvps.com/xperts64

http://mvp.support.microsoft.com/profile/charlie.russel

"Homer J. Simpson" <root@127.0.0.1> wrote in message

news:%231$z$xPCIHA.4956@TK2MSFTNGP06.phx.gbl...

> Thanks to all who replied. I knew the most straightforward thing to do

> was to reduce the size of the C: partition down to nothing (and reallocate

> its space to D:), and leave the boot files there, but my preference

> would've been to remove it completely. I thought something like Acronis

> would've been able to change my D: partition from Extended to Primary, but

> if it can't do that, then it looks like I'm really SOL.

>

October 7, 2007

Re: Getting rid of an old bootable partition...

Charlie Russel - MVP wrote:

> Acronis will do that, I think. BUT, you'll still end up with problems.

> Now the computer will think that your system drive is C: not D: (and you

> can't change the assigned drive letter of a system partition.) That

> would break way more than just Windows, which could probably sort of

> cope. And when you were all done? You'd have an odd machine that didn't

> behave normally. To my mind, that leaves two possibilities - leave the

> legacy C: there, or re-partition and rebuild.

>

If the system drive letter has to be manipulated, you go to the registry:

HKEY_LOCAL_MACHINE\SYSTEM\MountedDevices

disk id + position of partition determines which drive letter is assigned

October 8, 2007

Re: Getting rid of an old bootable partition...

You still have all the shortcuts and other associations in the registry that

would still refer to D. Also, the knowledgebase strongly recommends against

doing that for the system drive unless it can't be booted anyway.

"jorgen" <na@invalid> wrote in message

news:eS9imUSCIHA.4176@TK2MSFTNGP06.phx.gbl...

> Charlie Russel - MVP wrote:

>> Acronis will do that, I think. BUT, you'll still end up with problems.

>> Now the computer will think that your system drive is C: not D: (and you

>> can't change the assigned drive letter of a system partition.) That would

>> break way more than just Windows, which could probably sort of cope. And

>> when you were all done? You'd have an odd machine that didn't behave

>> normally. To my mind, that leaves two possibilities - leave the legacy C:

>> there, or re-partition and rebuild.

>>

>

> If the system drive letter has to be manipulated, you go to the registry:

>

> HKEY_LOCAL_MACHINE\SYSTEM\MountedDevices

>

> disk id + position of partition determines which drive letter is assigned

October 8, 2007

Re: Getting rid of an old bootable partition...

I think you can only do that if you are restoring a backup, but would be

possible that way. I agree 100% that it should be done as you recommended.

"Charlie Russel - MVP" <charlie@mvKILLALLSPAMMERSps.org> wrote in message

news:9EFE9D30-14A4-4578-9846-4F2577BED952@microsoft.com...

> Acronis will do that, I think. BUT, you'll still end up with problems. Now

> the computer will think that your system drive is C: not D: (and you can't

> change the assigned drive letter of a system partition.) That would break

> way more than just Windows, which could probably sort of cope. And when

> you were all done? You'd have an odd machine that didn't behave normally.

> To my mind, that leaves two possibilities - leave the legacy C: there, or

> re-partition and rebuild.

>

> --

> Charlie.

> http://msmvps.com/xperts64

> http://mvp.support.microsoft.com/profile/charlie.russel

>

> "Homer J. Simpson" <root@127.0.0.1> wrote in message

> news:%231$z$xPCIHA.4956@TK2MSFTNGP06.phx.gbl...

>> Thanks to all who replied. I knew the most straightforward thing to do

>> was to reduce the size of the C: partition down to nothing (and

>> reallocate its space to D:), and leave the boot files there, but my

>> preference would've been to remove it completely. I thought something

>> like Acronis would've been able to change my D: partition from Extended

>> to Primary, but if it can't do that, then it looks like I'm really SOL.

>>

>

October 8, 2007

Re: Getting rid of an old bootable partition...

John Barnes wrote:

> You still have all the shortcuts and other associations in the registry

> that would still refer to D. Also, the knowledgebase strongly

> recommends against doing that for the system drive unless it can't be

> booted anyway.

The point was, if Windows wants to call the new system partition for C:

(it can happen) you can change it back to D: by editing the registry

October 8, 2007

Re: Getting rid of an old bootable partition...

Sorry, interpreted you differently.

"jorgen" <na@invalid> wrote in message

news:eincSZZCIHA.3400@TK2MSFTNGP03.phx.gbl...

> John Barnes wrote:

>> You still have all the shortcuts and other associations in the registry

>> that would still refer to D. Also, the knowledgebase strongly recommends

>> against doing that for the system drive unless it can't be booted anyway.

>

> The point was, if Windows wants to call the new system partition for C:

> (it can happen) you can change it back to D: by editing the registry

October 8, 2007

Re: Getting rid of an old bootable partition...

> Acronis will do that, I think. BUT, you'll still end up with problems. Now

> the computer will think that your system drive is C: not D: (and you can't

> change the assigned drive letter of a system partition.) That would break

> way more than just Windows, which could probably sort of cope. And when

> you were all done? You'd have an odd machine that didn't behave normally.

> To my mind, that leaves two possibilities - leave the legacy C: there, or

> re-partition and rebuild.

What, exactly, would cause the drive letter reassignment? Windows itself?

Acronis?

I'm asking 'cuz I remember a coworker of mine a couple of years ago had a

machine with a multiboot setup, with his main OS on a separate drive (H:)

and after much hardware shuffling, he ended up with his primary OS still on

H: drive, and without a C: partition at all (eg, the C: drive/partition was

removed and nothing ever attempted to reassign a different drive letter to

the OS). So I'm guessing it's not entirely impossible...

Mind you, I'm not *that* hell-bent on getting rid of the partition; I'd

rather leave it at that than find out the hard way it's not gonna work. A

reinstall is the last thing on my to-do list right now...

October 8, 2007

Re: Getting rid of an old bootable partition...

Homer J. Simpson wrote:

> What, exactly, would cause the drive letter reassignment? Windows itself?

> Acronis?

The way Windows identify partitions is by disk id (stored in MBR) and

where the partition starts (sector count). So when you move the

partition, the signature in registry is no longer valid, and it will

reassign.

October 8, 2007

Re: Getting rid of an old bootable partition...

Homer:

If I were you, I would simply use partition C: for valuable data storage.

My Documents, Outlook database (oulook.pst file) or whatever database your

e-mail/contacts program uses, etc., etc., etc., can be relocated there.

That way...

1.- Backing up your important info is just backing up C:

2.- You can always wipe out your OS from drive D: (because of reinstalling,

new OS, etc.) without being afraid of losing all that you care for.

Carlos

"Homer J. Simpson" wrote:

> > Acronis will do that, I think. BUT, you'll still end up with problems. Now

> > the computer will think that your system drive is C: not D: (and you can't

> > change the assigned drive letter of a system partition.) That would break

> > way more than just Windows, which could probably sort of cope. And when

> > you were all done? You'd have an odd machine that didn't behave normally.

> > To my mind, that leaves two possibilities - leave the legacy C: there, or

> > re-partition and rebuild.

>

> What, exactly, would cause the drive letter reassignment? Windows itself?

> Acronis?

>

> I'm asking 'cuz I remember a coworker of mine a couple of years ago had a

> machine with a multiboot setup, with his main OS on a separate drive (H:)

> and after much hardware shuffling, he ended up with his primary OS still on

> H: drive, and without a C: partition at all (eg, the C: drive/partition was

> removed and nothing ever attempted to reassign a different drive letter to

> the OS). So I'm guessing it's not entirely impossible...

>

> Mind you, I'm not *that* hell-bent on getting rid of the partition; I'd

> rather leave it at that than find out the hard way it's not gonna work. A

> reinstall is the last thing on my to-do list right now...

>

October 8, 2007

Re: Getting rid of an old bootable partition...

Your problem is the logical drive that you can't put your system files on

and boot. Acronis does not assign drive letters.

"Homer J. Simpson" <root@127.0.0.1> wrote in message

news:u83A2rcCIHA.4236@TK2MSFTNGP02.phx.gbl...

>> Acronis will do that, I think. BUT, you'll still end up with problems.

>> Now the computer will think that your system drive is C: not D: (and you

>> can't change the assigned drive letter of a system partition.) That would

>> break way more than just Windows, which could probably sort of cope. And

>> when you were all done? You'd have an odd machine that didn't behave

>> normally. To my mind, that leaves two possibilities - leave the legacy C:

>> there, or re-partition and rebuild.

>

> What, exactly, would cause the drive letter reassignment? Windows itself?

> Acronis?

>

> I'm asking 'cuz I remember a coworker of mine a couple of years ago had a

> machine with a multiboot setup, with his main OS on a separate drive (H:)

> and after much hardware shuffling, he ended up with his primary OS still

> on H: drive, and without a C: partition at all (eg, the C: drive/partition

> was removed and nothing ever attempted to reassign a different drive

> letter to the OS). So I'm guessing it's not entirely impossible...

>

> Mind you, I'm not *that* hell-bent on getting rid of the partition; I'd

> rather leave it at that than find out the hard way it's not gonna work. A

> reinstall is the last thing on my to-do list right now...

>

October 8, 2007

Re: Getting rid of an old bootable partition...

> If I were you, I would simply use partition C: for valuable data storage.

> My Documents, Outlook database (oulook.pst file) or whatever database your

> e-mail/contacts program uses, etc., etc., etc., can be relocated there.

> That way...

> 1.- Backing up your important info is just backing up C:

> 2.- You can always wipe out your OS from drive D: (because of

> reinstalling,

> new OS, etc.) without being afraid of losing all that you care for.

Actually, I've been doing this for years. Just not as drive C:.

October 11, 2007

Re: Getting rid of an old bootable partition...

On Sat, 6 Oct 2007 12:49:55 -0400, "Homer J. Simpson" <root@127.0.0.1>

wrote:

>Hi all,

>

>I used to have XP 32-bit on my C: drive. Shortly after XP 64-bit came out,

>I installed in on D: and started dual-booting. It didn't take long after

>I've completed my migration that I started using x64 exclusively. My

>system's gone through a few hardware changes since then, but I've never

>bothered to reboot in XP 32-bit to install drivers and such. A while ago I

>did try to boot into XP 32-bit (can't remember why I would do such a foolish

>thing) ;-) but I found out at that time that my 32-bit installation was

>corrupted.

>

>I can't say I cared enough about it to try to fix it or even figure out why

>it wasn't functional anymore. In fact I'd prefer to have it gone

>completely.

>

>Both partitions (C: and D:) are 30GB in size, on the same physical hard

>drive (250GB SATA). The C: partition (obviously in such a setup) contains

>the boot.ini file. Given that I have no need for XP 32-bit, and my D:

>partition could use the space, I thought I could get rid of the C: partition

>entirely.

>

>So I'm asking for advice on exactly how I could proceed, given that XP's

>disk manager doesn't really have the smarts to do such a thing.

>

>At a minimum I would expect I would have to copy the boot.ini, ntdetect.com

>and ntldr files from C: to D: before I blow away the C: partition (and

>resize D: to take up that free space)...maybe edit the boot.ini so any

>reference to ...rdisk(0)partition(2) becomes rdisk(0)partition(1)...but then

>I'm pretty sure I'll run into further problems because C: drive is currently

>a primary partition, while D: (and E:, F:, G:, and a couple more) are all

>logical partitions grouped within one extended partition.

>

>I'm not looking to change XP x64's drive letter assignment from D: back to

>C:...in fact if it does that, that'll screw up *all* references pretty good.

>I just want the C: partition to go away.

>

>I know that at least one of these steps isn't supported by Disk Manager

>itself (resizing my D: partition), so I'm looking for a good tool (Partition

>Magic, or something from Acronis?) that is *known* to be able to do these

>sort of changes intelligently and won't leave me with a system that won't

>boot...

>

>Anybody gone through this process?

>

You have to, in a nutshell, accomplish two tasks: 1) copy the four XP

x64 folders to the primary partition, and 2) modify the registry of

the copied XP x64 so it sees the primary partition as D: instead of

C:.

One way to perform task 1 is to install another copy of Windows XP in

one of the other partitions, and use the program xxcopy to copy XP x64

from D: to C:.

1. Copy boot.ini, ntldr and ntdetect.com from C:\ to D:\

Microsoft Windows [Version 5.2.3790]

D:\Documents and Settings\Administrator>cd \

D:\>c:

C:\>attrib

A C:\AUTOEXEC.BAT

A SH C:\boot.ini

A C:\CONFIG.SYS

A SHR C:\IO.SYS

A SHR C:\MSDOS.SYS

A SHR C:\NTDETECT.COM

A SHR C:\ntldr

A SH C:\pagefile.sys

C:\>xcopy boot.ini d:\ /h

C:boot.ini

1 File(s) copied

C:\>xcopy nt*.* e:\ /h

C:NTDETECT.COM

C:ntldr

2 File(s) copied

C:\>d:

D:\>attrib

A SH D:\boot.ini

A SH D:\NTDETECT.COM

A SH D:\ntldr

A SH D:\pagefile.sys

D:\>

2. Install XP in E:, and boot XP from it.

3. Install xxcopy.

E:\>xxcopy

============== XXCOPY ==========================================

Welcome to the Wonderful World of XXCOPY

XXCOPY is a feature-packed file management tool for all PC users.

For IT professionals, it's good for system/network administration.

For small business, and home users, XXCOPY offers a wide variety

of functions from a simple file copy to a complex system backup.

Do you want to proceed with XXCOPY installation? (Y/N) : Y

============== Verification of License Status ====================

The current copy of the XXCOPY executable was launched from

E:\

We recommend XXCOPY be stored (with other supporting files)

in the following directory (to become XXCOPY's home)

E:\WINDOWS\system32\

Do you want to make it as XXCOPY's home directory (Y/N) ? Y

Copied E:\WINDOWS\system32\XXCOPY.EXE

XXCOPY installation completed.

4. Use xxcopy to copy XP x64 from D: to C:

E:\>xxcopy d:\*.* c:\ /clone /oNErrorLog.txt

===== Caution!!! ====================================

This version of XXCOPY has never been tested

in the current Operating System environment.

You should acquire the latest version of XXCOPY

from the XXCOPY web site (http://www.xxcopy.com).

Run this program at your own risk.

Press any key except <ESC> within 2 minutes to continue.

Otherwise, the program will terminate automatically.

##### WARNING!!! ##### WARNING!!! ##### WARNING!!! ##### WARNING!!!

#####

Make sure Source (D:) and Destination (C:) are correct.

This command will delete extra files/directories in the destination!

Press Ctrl-C to abort, any other key to begin deleting/copying

file(s).

==== ErrorLog.txt ====

Source base directory = "D:\"

Destination directory = "C:\"

File name template = "*.*"

D:\System Volume Information\MountPointManagerRemoteDatabase Copy

failed

D:\System Volume Information\tracking.log Copy failed

D:\System Volume

Information\_restore{1B224DD8-23C5-47AC-A5FB-39B77F29FB0B}\RP2\change.log

Copy failed

D:\System Volume

Information\_restore{CC4CAC4B-8BBA-48F9-A913-B093E29BE971}\RP2\change.log

Copy failed

D:\WINDOWS\Prefetch\NTOSBOOT-B00DFAAD.pf Copy failed

D:\WINDOWS\Prefetch\SETUP.EXE-393E66AE.pf Copy failed

~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Directories processed = 910

Total data in bytes = 2,191,898,696

Elapsed time in sec. = g

Action speed (MB/min) = g

Files examined = 12,126

Files copied = 12,116

Directories created = 485

Directories deleted = 237

Files copy failed = 6

Log File Created = E:\ErrorLog.txt

Exit code = 106 (Exit code is the number of failures plus

100)

To perform task 2 use regedit.

1. Start > Run > regedit

2. Click on HKEY_LOCAL_MACHINE

3. File > Load Hive...

4. from C:\Windows\System32\Config\SYSTEM

5. Give it a key name DriveC

6. Click on HKEY_LOCAL_MACHINE\DriveC\MountedDevices

7. Right click on \DosDevices\D: > Rename to \DosDevices\X:

8. Right click on \DosDevices\C: > Rename to \DosDevices\D:

9. Click on DriveC

10. File > Unload Hive...

11. File > Exit

Reboot. You now have two working copies of XP x64: the original

<http://tinypic.com/view.php?pic=2s00g1x&s=2>

and its copy.

<http://tinypic.com/view.php?pic=x36b9t&s=2>

Sign In

Getting rid of an old bootable partition...

Recommended Posts

Guest Homer J. Simpson

Popular Days

Popular Days

Guest Charlie Russel - MVP

Guest thecreator

Guest Carlos

Guest John Barnes

Guest Charlie Russel - MVP

Guest Homer J. Simpson

Guest Charlie Russel - MVP

Guest jorgen

Guest John Barnes

Guest John Barnes

Guest jorgen

Guest John Barnes

Guest Homer J. Simpson

Guest jorgen

Guest Carlos

Guest John Barnes

Guest Homer J. Simpson

Guest Andy

Similar Content

getting into old icloud account

Can't get rid of the defaultuser0

Old Member Returns

How to get rid of Windows Installation?

Fully get rid of MS gaming overlay

Browse

Activity

Site Info